FarragTech CARD G Скачать руководство пользователя страница 63

Страница: 63 / 101

EXTENDED MODE

CARD G / FIT

V 6.15 E / April 2010

17.7.2

WEEKLY TIMER LOADING

he loading of the drying hopper can be

started and stopped through a discrete weekly timer.
The W

EEKLY

IMER

OADING

is accessed from the screen W

EEKLY

IMER

ENERAL

with the

key .

The switching times become visible as soon as the weekly timer is activated. One ON-time and
one OFF-time can be set per day.
The same rules as described in chapter 17.7.1 W

EEKLY

IMER

ENERAL

on page 58 apply for setting

the switching times.
Three weekly timer programs have been pre-set which can be enabled or reprogrammed by the
operator (see chapter 17.7.1 W

EEKLY

IMER

ENERAL

on page 58 for detailed information).

Only the drying process will be controlled by the G

ENERAL

EEKLY

IMER

if the

EEKLY

IMER FOR

OADING

is activated. It can be deactivated without affecting

the proper function of the W

EEKLY

IMER FOR

OADING

Independent from which weekly timer and switching program is chosen, the
loading process can always be activated or deactivated by using the keys

at the same time. The weekly timer starts or stops the loading process

at the next valid switching time.

Содержание CARD G






































































































Результаты поиска

Содержание CARD G

Отзывы:

Похожие инструкции для CARD G

Бренды по названию

Популярные бренды

FarragTech CARD G, Руководство по эксплуатации

Результаты поиска

Содержание CARD G

Отзывы:

Похожие инструкции для CARD G

Бренды по названию

Популярные бренды