FarragTech CARD G Скачать руководство пользователя страница 64

Страница: 64 / 101

EXTENDED MODE

CARD G / FIT

V 6.15 E / April 2010

17.7.3

DATE AND TIME

he menu to set D

ATE AND

IME

is accessed from the screen W

EEKLY

IMER

ENERAL

or W

EEKLY

IMER

ENERAL

OADING

with the key

The accurate date and time are important to get correct information in the S

TATUS

EPORT

and in

the F

AULTS

CREEN

. Using automatic operation through the W

EEKLY

IMERS

also depends on the

correct settings for date and time in this screen.

Pressing

simultaneously activates the setting procedure.

The time stops, and a blinking cursor appears. The E

DITOR

CREEN

needs to be used to enter the

numeric values. The weekday can be directly selected with the

key.

To accept the new values the keys

need to be pressed at the same time.

The key

is to be pressed to abandon this screen.

Содержание CARD G






































































































Результаты поиска

Содержание CARD G

Отзывы:

Похожие инструкции для CARD G

Бренды по названию

Популярные бренды

FarragTech CARD G, Руководство по эксплуатации

Результаты поиска

Содержание CARD G

Отзывы:

Похожие инструкции для CARD G

Бренды по названию

Популярные бренды