FarragTech CARD G Скачать руководство пользователя страница 53

Страница: 53 / 101

EXTENDED MODE

CARD G / FIT

V 6.15 E / April 2010

Hint:
There is an output on the FIT-controller which supplies 24V DC as soon as
CDOWN timer and RAMP timer (if activated) are expired. If both timers are set

to 0h 0m, the output will supply 24V DC immediately after the drying process
has been started.
If a retrofit is desired, contact

or its local representative for

further instructions.

SLEEP Temperature

ACTORY

ETTING

: 50°C [122°F]

The SLEEP M

ODE

protects the resin in the CARD G FIT against degradation. As soon as the SLEEP T

IMER

has expired (see next parameter) or the keys

have been pressed, the drying temperature is

lowered to the SLEEP T

EMPERATURE

This value must never be higher than the value SET

EMPERATURE

If so, it is automatically corrected by

the FIT-controller.

SLEEP Timer

ACTORY

ETTING

0h 0m

The SLEEP

IMER

is released from a loading unit or from an external signal connected to the

CARD G FIT unit. The timer will be reset to its initial value if the signal is revoked.
The air temperature will be lowered to the SLEEP

EMPERATURE

(see previous parameter) after the

SLEEP

IMER

has expired. The SET T

EMPERATURE

is loaded as soon as the S

LEEP SIGNAL

is released again.

The time is to be set to 0h 0m if the SLEEP

ODE

is not desired.

Pressing

at the same time allows the operator to activate or

deactivate the SLEEP

ODE

immediately provided that the drying process is

switched on.
If a loading device is not used to fill the drying hopper, the SLEEP T

IMER

can be

controlled by an external signal which needs to be connected to the plug (3.2)

on the CARD G FIT.

RAMP Temperature

ACTORY

ETTING

: -30°C [-54°F]

If the RAMP T

IMER

(see next parameter) is activated, the resin will first be heated up to this temperature

after the drying process has been started.
This value is set as a difference to the SET T

EMPERATURE

. It must never be higher than that one. If so, it is

automatically corrected by the FIT-controller.

Содержание CARD G






































































































Результаты поиска

Содержание CARD G

Отзывы:

Похожие инструкции для CARD G

Бренды по названию

Популярные бренды

FarragTech CARD G, Руководство по эксплуатации

Результаты поиска

Содержание CARD G

Отзывы:

Похожие инструкции для CARD G

Бренды по названию

Популярные бренды