FarmTek FodderPro Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 41

background image

11

Revision date: 09.21.18

112712

4

INSTALL CABLES—FDCAB13L0703S1T (continued)

5. With assistance, place the 108503 bracket against the frame tube and mark the hole position using a marker.

NOTE:

Adjust the position of the bracket on the frame leg to allow the cable to sag an inch or so. This ensures sufficient adjustment when it is time to

plumb the vertical frame tubes.

Install Cables

6. Add a FAME51B washer to a Tek screw and attach the 108503 bracket with cable assembly to the frame tube. Tek screw should be snug.

Do not

overtighten!

Doing so will strip the threads from the hole.

7. Repeat these steps to install the remaining cable assembly for the first pod frame.
8. After installing both cable assemblies, evenly tighten each turnbuckle to remove cable slack. If you run out of turnbuckle adjustment and slack remains,

loosen the turnbuckle and lower the 108503 bracket on the frame. Retighten to remove slack.

9. With assistance, carefully adjust the frame to position it on the site where the entire fodder system will be assembled. Review the diagrams near the end of

this guide for details.

10. Continue with the next procedure.

Step 5

Move bracket

and cable

assembly up or

down to achieve

the best fit.

Mark hole position.

«
...
9
10
11
12
13
...
»

Содержание FodderPro










































Отзывы:

Нет отзывов

Похожие инструкции для FodderPro

Бренд: ZIGBEE Страницы: 4

Бренд: CAIRE Страницы: 38

Бренд: Caframo Страницы: 72

Бренд: Water Witch Страницы: 2

Бренд: Falltech Страницы: 48

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Страницы: 12

Бренд: Hanil Страницы: 24

Бренд: Hanil Страницы: 32

Бренд: Hanil Страницы: 24

Бренд: TDR Страницы: 8

Бренд: Walimex Pro Страницы: 44

Бренд: Feniex Страницы: 5

Бренд: Toro Страницы: 12

Бренд: AGI Страницы: 33

Бренд: DALBO Страницы: 27

Infinity Wash XL

Бренд: Coemar Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды