FarmTek FodderPro Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 41

background image

66

112712

Revision date: 09.21.18

1

GATHER THE 35-TRAY FRAME COMPONENTS

Follow the basic steps noted below to assemble the 35-tray pod frame.

ATTENTION:

A solid, level surface such as concrete capable of supporting the frame and fodder is required. If a full concrete slab is not part of the

building, install concrete blocks or pavers, or pour small concrete slabs level with the finished grade to support the frame tubes.

Required parts for this pod:

•  (2) FD15VMGL08575S1 (Back Vertical Tube)
•  (2) FD15VMGL07225S2 (Front Vertical Tube)
•  (14) FD15LMGL06900S1 (Front-to-Back Side Tube)
•  (15) FD15HMGL08000S1 (Horizontal Tube—Ends)
•  (14) FD15CMGL07350S1 (Horizontal Tube—Mid)
•  112772 (5/16" x 3") Flathead Bolt
•  FAG338 (5/16" x 3") Hex Cap Bolt
•  FAME51B (5/16") Flat Washer

Complete these steps:

1. Identify and collect the parts needed to assemble the

35-tray pod frame

. See diagram to the right.

2. Install the levelers at the bottom of each vertical

frame tube. (See Procedure 2.)

3. Assemble the front (drain end) and back (supply

end) main frames. (See Procedure 2.)

4. Assemble the center frame sections that connect the

end frames. (See Procedure 3.)

5. Attach the diagonal cable assemblies to one side of

the frame. (See Procedure 4.)

6. Set the assembled frame in position and level and

plumb the frame. (See Procedure 5.)

7. Continue with Procedure 6.

General Frame Assembly Information

BACK

FRONT

FD15VMGL

08575S1

85-3/4"

FD15VMGL

07225S2

72-1/4"

FD15LMGL

06900S1

69"

FD15CMGL

07350S1

73-1/2"

FD15HMGL

08000S1

80"

FD15HMGL

08000S1

80"

«
...
4
5
6
7
8
...
»

Содержание FodderPro










































Отзывы:

Нет отзывов

Похожие инструкции для FodderPro

Бренд: BACtrack Страницы: 16

Бренд: Rangevision Страницы: 28

Бренд: Danelec Страницы: 67

Бренд: Pahlen Страницы: 20

Бренд: Paia Страницы: 7

Бренд: U Technology Страницы: 6

Бренд: Garmin Страницы: 2

Бренд: Hameg Страницы: 39

Бренд: Vari Lite Страницы: 6

Бренд: OCEM Страницы: 37

Бренд: Aqua Creek Products Страницы: 3

Бренд: HIPOTRONICS Страницы: 27

Бренд: Major tech Страницы: 20

Бренд: Xante Страницы: 27

Бренд: Celco Страницы: 2

Lighting Systems Baselyte-BSL18

Бренд: Lightolier Страницы: 4

Бренд: ACME Страницы: 32

5-foot Farm Wall

Бренд: ZipGrow Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды