FarmTek FodderPro Скачать руководство пользователя страница 8

Страница: 8 / 41

112712

Revision date: 09.21.18

ASSEMBLE END FRAMES

ATTENTION:

A solid, level surface such as concrete capable of supporting the frame and fodder is required. If a full concrete slab is not part of the

building, install concrete blocks or pavers, or pour small concrete slabs level with the finished grade to support the frame tubes.

Assemble each

frame in the location where it will ultimately be positioned.

Other than minor adjustments in position for leveling, moving the frames

after assembly is not recommended.

Assemble Main Frame—Ends

IMPORTANT:

After assembling the frame sections as shown in Procedures

2-4, set the frame in position and complete Procedure 5 to level and plumb

the frame

before assembling the next pod

Do not allow the frame to

stand without the cables installed and adjusted. Brace frame before

cable installation!

Complete these steps to install each 112477 insert:
1. Slide one 112477 insert into the bottom of a vertical

end frame tube. Tap gently with a small hammer if

needed to seat in place.

2. Secure using a 112838 Tek screw.

Install screw

through frame tube and wall of the 112477

insert.

3. Adjust the FAH337B bolt so that it is fully turned

into the threaded plate of the insert. See photo to

the right.

CAUTION:

Frames are heavy! Assemble

the frame where it will be positioned in the

building. To prevent damage, injury, or both,

do not move an assembled frame!

112772

5/16" x 3" Flat

Head Bolt

During the frame assembly, position the vertical tubes

so the large diameter bolt hole is to the outside of the

frame tube. This provides a seat for the tapered head

of the 112772 bolt.

Front

Back

112722

112477

FAH337B

FALB34B

Bottom

of Frame

Tube

112477

Install Tek screw on either side

of the center line to prevent

contact with adjusting bolt.

STEP 3

Содержание FodderPro










































Результаты поиска

Содержание FodderPro

Отзывы:

Похожие инструкции для FodderPro

Бренды по названию

Популярные бренды

FarmTek FodderPro, Руководство пользователя

Результаты поиска

Содержание FodderPro

Отзывы:

Похожие инструкции для FodderPro

Бренды по названию

Популярные бренды