FarmTek FodderPro Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 41

background image

15

Revision date: 09.21.18

112712

6

Install Gutters

INSTALL GUTTERS—continued

Complete these steps:
1. Using the diagram on the previous page, pick the gutter section

and set it in place on the pod frame.

2. Ensure that the gutter slopes toward the downspout location

shown on the diagram.

ATTENTION:

Downspouts are installed

after

all gutters are

installed.

3. Set all trays in place on the frame where gutter was installed.
4. Mark two (2) locations between trays at each end of the gutter.

ATTENTION:

Position all fasteners between the two trays at

each end of each gutter regardless of how many trays are on

each pod level.

5. Remove the trays and drive a 112838 Tek screw through the

gutter and into the frame tube at the locations chosen in Step 4.

6. Repeat this procedure to install all remaining gutters.
7. Continue with the installation of the downspouts.

STEP 5

STEP 4

STEP 6

STEP 3

Set trays on frame to judge where to install

fasteners to secure gutter to frame.

Slide trays back from gutter to allow for the

installation of the 112838 fasteners.

Center fastener location so screw head does

not contact any part of any tray.

Photo shows trays in position with fastener

installed to secure gutter.

Screw Locaton

Photo shows installed gutter. Dashed arrow

indicates direction of water flow.

STEP 2

Gutter end

is tight to

frame tube.

STEP 1

Photo shows crimped or high end of gutter,

which is opposite the drain end.

«
...
13
14
15
16
17
...
»

Содержание FodderPro










































Отзывы:

Нет отзывов

Похожие инструкции для FodderPro

Бренд: 4EVAC Страницы: 27

Бренд: Danelec Страницы: 67

Бренд: EarthQuake Страницы: 12

Бренд: Madsen Страницы: 206

Бренд: Raymarine Страницы: 3

SmartPilot ST8002

Бренд: Raymarine Страницы: 48

Бренд: Raymarine Страницы: 38

hsb2 PLUS Series

Бренд: Raymarine Страницы: 248

Бренд: Feniex Страницы: 5

Бренд: Kanlux Страницы: 4

EPL-HB-150LED-RT-IBSC

Бренд: Larson Electronics Страницы: 2

Бренд: Emos Страницы: 8

Street Bar IP65 16x3W TW

Бренд: Varytec Страницы: 52

Бренд: OttLite Страницы: 2

Бренд: Xaoc Devices Страницы: 6

Бренд: Behringer Страницы: 4

Бренд: SGM Страницы: 20

Бренд: Trac Vac Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды