FarmTek FodderPro Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 41

background image

29

Revision date: 09.21.18

112712

12

Replacing the 110414 Adapter and 110406 Emitter

Adapters and emitters are easily replaced if broken or damaged. Complete these steps:
1. Using a small punch or similar tool, carefully push the broken portion of the 110414 adapter

into the 1/2” pvc supply tube

.

ATTENTION:

Remove horizontal tube from vertical manifold pipe if needed. Tool used to push broken adapter into pvc tube must

have a diameter smaller than the hole in pvc tube.

Do not damage the adapter hole in the pvc tube.

2. Once the broken adapter is pushed into tube, align replacement 110414 adapter with hole in pvc tube and gently grip with adjustable

pliers as shown below in Photo 1. Assure the adapter is straight in line with the axis of hole.

3.  Gently squeeze pliers until adapter is seated and locked into pvc tube.
4.  Align tapered end of the 110406 emitter with new adapter as shown in Photo 2 and press the emitter into the adapter.
5.  Check emitter. Assure that it is fully seated.
6.  Attach horizontal supply tube to vertical manifold pipe if it was removed.
7.  Test operation.

Replacing the 110414 Adapter and 110406 Emitter

110406*

110414*

1

Press new adapter into hole

in horizontal pvc tube.

2

Press emitter into the new

adapter. Test operation.

«
...
27
28
29
30
31
...
»

Содержание FodderPro










































Отзывы:

Нет отзывов

Похожие инструкции для FodderPro

Бренд: KaVo Страницы: 13

Бренд: Bante Instruments Страницы: 6

Бренд: Gaspardo Страницы: 16

Бренд: HANYOUNG NUX Страницы: 2

Бренд: Panta Safe Light Страницы: 2

Бренд: QMAXZ Lighting Страницы: 36

Бренд: Tar River Страницы: 44

Бренд: Tar River Страницы: 61

Бренд: Walinga Страницы: 20

Бренд: Tieline Страницы: 359

Бренд: SereneLife Страницы: 4

Бренд: KUHN Страницы: 44

Бренд: MAHA Страницы: 138

Бренд: American DJ Страницы: 8

Бренд: Civemasa Страницы: 55

Бренд: Heitronic Страницы: 16

Бренд: Echo Страницы: 18

Бренд: Laserworld Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды