FarmTek 113539 страница 11 Скачать руководство пользователя

Страница: 11 / 31

Revision date: 01.13.21

113539

Assembly Instructions

Complete these steps to drill holes for nutrient tubes:
1. Take half of the channel lids and arrange so all plant holes and ends align. Take the remaining channel lids

and repeat this step. Keep the two piles separate.

ATTENTION:

For the first pile of lids, position nutrient tube holes where first plant hole is closest to the lid

end. See A in the photo.

For the remaining lids, position nutrient tube holes where first plant hole is farthest from lid end. See B in the

photo.

2. Move to pile A and drill two (2) 5/16" holes in each lid where plant hole is closest to lid end. See diagram that

follows. Keep lids in the same group when completed.

Spacing

For improved plant growth, off-set holes when installing lids. Alternate lids as shown below and on

previous page. Before snapping lids onto channels, drill the nutrient tube holes at one end of each lid.

Photo shows lids installed

so plant holes are offset.

Nutrient Tube

Holes

3. Move to pile B and drill two (2) 5/16" holes in each lid where plant hole is farthest from lid end. See diagram

that follows. Keep lids in the same group when completed.

ATTENTION:

Example above continues the example shown on previous page. Actual hole pattern may not

resemble what is shown in this example. Whatever the hole pattern, when sliding lids onto channels, position

nutrient tube holes opposite the drain end/elbow of the channel.

ATTENTION:

Drill holes away from open

channels to prevent debris from dropping

into channels.

Space holes

2" apart.

1/2" to 3/4"

from end.

Space holes

2" apart.

1/2" to 3/4"

from end.

PREPARE THE 8' CHANNEL LIDS (continued)

Hole closest to end.

Hole farthest from end.

Содержание 113539
































Результаты поиска

Содержание 113539

Отзывы:

Похожие инструкции для 113539

Бренды по названию

Популярные бренды

FarmTek 113539, Руководство пользователя

Результаты поиска

Содержание 113539

Отзывы:

Похожие инструкции для 113539

Бренды по названию

Популярные бренды