FarmTek 113539 страница 7 Скачать руководство пользователя | Manualshive

Страница: 7 / 31

background image

7

Revision date: 01.13.21

113539

End

End

Assembly Instructions

6. With assistance, arrange and stand the two (2) base assemblies so leg lengths of each base assembly are aligned (i.e., 36" with 36", 34 3/4"

with 34 3/4", and so on). It is best to

construct support frame where it will be used

so frame can be leveled for final assembly.

7. Next, take the

three (3) 131P0495 pipes and cut each to 46"

. (Pipes can remain full length if you want a wider table. Adjust channel spacing

as needed.) These instructions use the 46" cross support. Channels are spaced at 10" on-center for the example throughout this manual.

8. Slide the 46" cross support through the tee fittings at one end of each base assembly. Repeat the step to install the center cross support and

remaining end cross support.

9. Set the width of the support frame at ground level and at the cross support . See the diagram below and in the Quick Start section near the

back of this guide.

10. Tighten all set screws to secure all connections.
11. Continue with the next procedure.

1

ASSEMBLE MAIN SUPPORT FRAME (continued)

Ground Level

Leg

46" Cross Support

End View of Support Frame

40"

Center-to-Center

40"

Center-to-Center

«
...
5
6
7
8
9
...
»

Содержание 113539
































Отзывы:

Нет отзывов

Похожие инструкции для 113539

Бренд: Radarcan Страницы: 40

Бренд: LAPPSET Страницы: 16

ST60+ SPEED INSTRUMENT

Бренд: Raymarine Страницы: 60

Бренд: Raymarine Страницы: 15

Бренд: Raven Страницы: 58

Бренд: Raven Страницы: 26

Бренд: Alcoscan Страницы: 6

INTRA PROPHYwiz 181 P

Бренд: KaVo Страницы: 22

Бренд: Grange Страницы: 2

Dual-Lite EVHC-BC Series

Бренд: Hubbell Страницы: 2

Бренд: Cooper Lighting Страницы: 1

Бренд: Partizzle Страницы: 8

PowerPlant PowerBank+ mk2

Бренд: Harley Benton Страницы: 2

HC-1500 - Type 2E

Бренд: Echo Страницы: 32

Бренд: Malibu Boats Страницы: 2

BI-FLEX M3 Bi-Color

Бренд: Alladin Страницы: 8

Бренд: Expolite Страницы: 34

Бренд: Waters Страницы: 198

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды