FarmTek 113539 страница 25 Скачать руководство пользователя

Страница: 25 / 31

Revision date: 01.13.21

113539

OPERATIONAL AND MAINTENANCE INFORMATION

General Cleaning and Maintenance Instructions

For optimal performance and to increase yields, check and clean the NFT

system periodically. Time between maintenance and cleaning depends

on the growing environment and specific use of the system. Complete the

following steps as needed to ensure that your system is working properly.
1. Inspect the frame and mounting screws to ensure they are tight and

frame is not damaged.

2. Disconnect the main power supply to turn off all pumps. Remove the

reservoir cover and inspect the inside of the reservoir. Reservoir should

be cleaned each time the nutrient solution is changed. Keep the reservoir

and porthole covers in place during operation to prevent light from

entering the reservoir.

3. Check all plumbing and main supply connections to ensure that all are

operating as designed.

4. Replace worn or cracked supply tubes as needed.
5. Clean the drain tube if needed. Remove the end plugs and inspect the

inside of the tube. Clean the drain tube by pulling or pushing a brush or

cloth through the it. Rinse with clean water.

NOTE:

Do not allow debris from the drain tube to contaminate the

contents of the reservoir. Remove the vertical tube and clean.

6. With the pump off, disassemble the filter and clean the screen and

housing. Reassemble for use. See procedure in the right column.

For best results, clean the filter screen regularly or when the flow rate

changes unexpectedly. Complete these steps to clean the filter screen.

1. Shutoff the power to the

nutrient pump. Open the

valve on the filter to drain the

system.

2. Grip the filter housing and the

main supply line and unscrew

the housing. Do not apply

force to the filter fittings.

Clean the Filter Screen and Housing

3. Remove the screen from the

housing. Using clean water,

rinse the housing and the

screen.

4. Insert the screen back into

the housing, reassemble the

filter, and

close the valve.

5. Turn on the pump and check

the flow from the supply tubes

to each channel.

6. Check filter for leaks.

Flow

Содержание 113539
































Результаты поиска

Содержание 113539

Отзывы:

Похожие инструкции для 113539

Бренды по названию

Популярные бренды

FarmTek 113539, Руководство пользователя

Результаты поиска

Содержание 113539

Отзывы:

Похожие инструкции для 113539

Бренды по названию

Популярные бренды