FarmTek 113539 страница 16 Скачать руководство пользователя | Manualshive

Страница: 16 / 31

background image

16

16

113539

Revision date: 01.13.21

9

Assembly Instructions

Complete these steps:
1. Cut a piece of 3/4" pvc tube from the 60" section supplied so it fits between the leg pipes. Allow

room to install the end fittings as shown below.

2. Slide a WF1530 elbow onto one end of the 28" pipe and a WF2990 cap onto the other end.

Do

not cement at this time.

ASSEMBLE NUTRIENT SUPPLY MANIFOLD AND ATTACH TO FRAME

3. Move to the frame and snap the supply manifold into the 3/4" hangers. Install so elbow is at the

corner opposite the tee fitting of the drain manifold at the opposite end of the frame.

WF2990

WF1530

4. Verify the open end of the elbow points towards the opposite end of the frame and mark elbow

location on both the elbow and manifold tube for alignment purposes.

5. Continue with the next procedure.

TOP VIEW

DIAGRAM

(not to scale)

Elbow installed at

corner opposite the

tee fitting of the drain

manifold.

Mark for alignment.

«
...
14
15
16
17
18
...
»

Содержание 113539
































Отзывы:

Нет отзывов

Похожие инструкции для 113539

Бренд: YSI Страницы: 70

Бренд: Salford Страницы: 64

Бренд: RASHA PROFESSIONAL Страницы: 11

Бренд: MADRIX Страницы: 24

Бренд: Bacharach Страницы: 48

Бренд: Mandam Страницы: 9

Бренд: IDEAL Networks Страницы: 8

Бренд: IDEAL Networks Страницы: 5

Бренд: Petzl Страницы: 15

Бренд: Pixlip Страницы: 15

Бренд: QTX Light Страницы: 4

Бренд: Hagen Страницы: 2

Бренд: Boss Audio Systems Страницы: 7

Бренд: American DJ Страницы: 8

aquajet-solar-oxygenator-v1

Бренд: Silicon Solar Страницы: 2

Бренд: DCI Edge Страницы: 14

Бренд: CTP Systems Страницы: 17

Бренд: FRC Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды