Farmet VIDIUM P 350 Скачать руководство пользователя | Manualshive

Страница: 21 / 24

background image

Manual

VIDIUM P 350 | P 450

21

│

24

7.

STORING THE MACHINE

When you put the machine out of operation for a longer-period of time:



Store the machine under a roof, if possible.



Store the machine on an even and solid ground with sufficient bearing capacity.



Clean the machine before storing and make sure that the machine is not damaged during the storage. Pay
special attention to all labelled lubricating places and lubricate the machine according to the lubrication
plan.



Apply grease to the spindles, sliding surfaces and ploughshares.



Leave the machine on the side to ensure sufficient stability!



Prevent access by unauthorised persons to the machine.

8.

LUBRICATION PLAN FOR THE MACHINE



Observe safety regulations when providing maintenance and lubricating the machine.



Regularly lubricate points

A-H

using a force feed lubricator (grease squirt) and regularly apply a layer of

grease to the spindles and sliding surfaces

I

and

J

.

Using high-quality lubricating grease increase the service life of the machine!

Manipulation with lubricants:

Protect yourself from direct contact with oils by using gloves or protective lotion.
Wash oil stains on skin thoroughly with warm water and soap. Do not clean the skin with petrol, diesel oil
or other dissolving agents.
Oil is poisonous. If you swallow any, immediately seek a doctor.



Keep lubricants out of reach of children.

«
...
19
20
21
22
23
...
»

Содержание VIDIUM P 350

























Отзывы:

Нет отзывов

Похожие инструкции для VIDIUM P 350

Бренд: ZOLL Страницы: 344

Бренд: ABB Страницы: 9

Бренд: Olsen Страницы: 56

Бренд: Waterous Страницы: 5

Бренд: 3TECH Страницы: 32

Бренд: 4EVAC Страницы: 15

Бренд: Haigh Страницы: 60

Бренд: Latham Страницы: 4

Бренд: SafeWaze Страницы: 23

Бренд: PAS Systems International Страницы: 24

MARK V Alcovisor

Бренд: PAS Systems International Страницы: 20

Бренд: PARRY Страницы: 14

Бренд: York Fitness Страницы: 36

Бренд: R&S Страницы: 371

Бренд: R.M. Young Страницы: 9

Бренд: Masterclock Страницы: 19

Quadra Force/Sys

Бренд: American DJ Страницы: 1

Бренд: Sunrise Medical Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды