Farmet KOMPAKTOMAT K1000PS Скачать руководство пользователя

Страница: 47 / 56

Manual

KOMPAKTOMAT K500PS | K600PS | K700PS | K800PS | K1000PS

│

RECOMMENDED TIGHTENING MOMENTS OF SCREW CONNECTIONS

SCREW CONNECTION

TIGHTENING

MOMENT

NOTE

M8x1

8Nm

Fastening set screws of bearings

M8 (8.8)

22Nm

Hook straps of arrow shares

M10 (8.8)

44Nm

Screws for chisel shares

M12 (8.8)

76Nm

House bearings attachment, hook screws of arrow shares,
joints on the axle, track cultivator flanges

M12 (10.9)

70Nm

Screws for attaching the blades to the leveller beam

M12 (12.9)

111Nm

Screws of arrow shares

M16 (8.8)

188Nm

Securing screws of the extensible beams for track
cultivators

M16 (8.8)

50Nm

Swing screws on track cultivators

M16 (8.8)

60Nm

Suspending share frames, folding levellers to the frames

M16 (10.9)

200Nm

Towing lug of the machine (C40, C50, C70, K80)

M20 (8.8)

365Nm

Prestress of tractive springs of front levellers

WHEEL NUT

M18x1,5

265Nm

Unbraked machines K500PS, K600PS, K700PS, K800PS,
K1000PS

M20x1,5

343Nm

Braked machines K500PS, K600PS, K700PS, K800PS,
K1000PS

HYD AIR JOINTS

M12x1,5

35Nm

Hydraulic screwing

M16x1,5

60Nm

Hydraulic screwing, air screwing

M22x1,5

140Nm

Hydraulic screwing, air screwing

Содержание KOMPAKTOMAT K1000PS

























































Результаты поиска

Содержание KOMPAKTOMAT K1000PS

Отзывы:

Похожие инструкции для KOMPAKTOMAT K1000PS

Бренды по названию

Популярные бренды

Farmet KOMPAKTOMAT K1000PS, Руководство по эксплуатации

Результаты поиска

Содержание KOMPAKTOMAT K1000PS

Отзывы:

Похожие инструкции для KOMPAKTOMAT K1000PS

Бренды по названию

Популярные бренды