Farmet KOMPAKTOMAT K1000PS Скачать руководство пользователя

Страница: 44 / 56

Manual

KOMPAKTOMAT K500PS | K600PS | K700PS | K800PS | K1000PS

│

9.2

WORKING POSITION OF THE KOMPAKTOMAT THREE-POINT HITCH
ARMS



The arms must be allowed to swivel in order to let the equipment aggregated to Kompaktomat freely
trace the terrain.



This is done as follows:

1. Moving support pins to the edge holes of the brackets.

2. Completely removing support pins.



Moving or removing support pins allows free terrain tracing of the machine aggregated to

Kompaktomat. At the same time, the rear roller of Kompaktomat will not be overloaded in the
working position.



Failure to observe this adjustment will damage the structure and rear roller of Kompaktomat, for

which the Manufacturer shall not be liable.

9.3

AGGREGATION WITH PNEUMATIC DRILL MACHINE



Pneumatic drill machines that have a fan driven by a fluid motor, not a drive shaft, may be aggregated
with Kompaktomat.



To aggregate Kompaktomat and the pneumatic drill machine with a fluid fan motor, Kompaktomat can
be optionally equipped with a hydraulic circuit for the fan drive.

9.3.1

FAN DRIVE CIRCUIT HC

A set of hydraulic components providing the transport of hydraulic oil from the tractor to the drill

machine.

The requirement regarding the connection of the hydraulic hose Dn 20- ISO20 directly into the tractor

oil tank, and not through the distributor, must be observed to ensure trouble-free function of the
circuit and the seed drill fan drive.

Dn 20 – ISO 20

Dn 12 – ISO 12,5

Содержание KOMPAKTOMAT K1000PS

























































Результаты поиска

Содержание KOMPAKTOMAT K1000PS

Отзывы:

Похожие инструкции для KOMPAKTOMAT K1000PS

Бренды по названию

Популярные бренды

Farmet KOMPAKTOMAT K1000PS, Руководство по эксплуатации

Результаты поиска

Содержание KOMPAKTOMAT K1000PS

Отзывы:

Похожие инструкции для KOMPAKTOMAT K1000PS

Бренды по названию

Популярные бренды