Farm King ALLIED 7420 Скачать руководство пользователя страница 16

Страница: 16 / 82

Safety - Pull Type 7420, 8420

Use Safety Rules

• Read and follow instructions in this manual and the

tractor’s Operators Manual before operating.

• Under no circumstances should young children be

allowed to work with this equipment.

• This equipment is dangerous to children and persons

unfamiliar with its operation.

• Check for overhead and / or underground lines before

operating equipment (if applicable).

• In addition to the design and configuration of

equipment, hazard control and accident prevention
are dependent upon the awareness, concern,
prudence and proper training of personnel involved
in the operation, transport, maintenance and storage
of equipment.

• Check that the equipment is securely fastened to the

tractor / towing vehicle.

• Make sure all the machine controls are in the

NEUTRAL position before starting the machine.

• Operate the equipment only from the operator’s

position.

• Operate the equipment according to the Operator

And Parts Manual.

• When learning to operate the equipment, do it at a

slow rate in an area clear of bystanders, especially
small children.

• DO NOT permit personnel to be in the work area

when operating the equipment.

• The equipment must be used ONLY on approved

tractors / transport vehicles.

• DO NOT modify the equipment in any way.

Unauthorized modification may impair the function
and / or safety and could affect the life of the
equipment.

• Stop tractor engine, place all controls in neutral,

set park brake, remove ignition key and wait for all
moving parts to stop before servicing, adjusting,
repairing, unplugging or filling.

• DO NOT make any adjustments or repairs on the

equipment while the machine is running.

• Keep shields and guards in place. Replace if damaged.

• Keep hands, feet, hair and clothing away from all

moving parts.

Safety Rules For Power Take-Off (PTO) Driven
Equipment

• Keep PTO shields and all guards in place. Replace

damaged or missing shields and guards before
operating.

• Follow warnings and instructions on machine signs

(decals). Replace damaged or missing decals.

• Do not wear loose or bulky clothing around the PTO

or other moving parts.

• Keep bystanders away from PTO driven equipment,

and never allow children near machines.

• Read and understand the manuals for the PTO

driven equipment and be aware of safe operating
procedures and hazards that may not be readily
apparent.

• Never operate over 540 rpm.

• Always walk around equipment to avoid coming

near a turning PTO driveline. Stepping over, leaning
across or crawling under a turning PTO driveline can
cause entanglement.

• Position the machine and equipment hitch correctly

to prevent driveline stress and separation.

• Use caution when turning. Turning too sharp can

cause driveline damage.

• Use caution when raising PTO driven equipment.

• Excessive driveline angle can cause driveline

damage. Use stops if needed.

• Maximum working PTO angle is 25 degrees.

Содержание ALLIED 7420



















































































Результаты поиска

Содержание ALLIED 7420

Отзывы:

Похожие инструкции для ALLIED 7420

Бренды по названию

Популярные бренды

Farm King ALLIED 7420, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание ALLIED 7420

Отзывы:

Похожие инструкции для ALLIED 7420

Бренды по названию

Популярные бренды