background image

37 

FRX100 VA S Housing Instruction Manual 20220601 

 

 

 

the housing should be rotated to a 

port down position 

and held that way as you return to the 

surface immediately and get it out of the water. 

17.

 

When mounting wet lenses on the housing lens port, it is recommended to follow the guidelines 
below in order to avoid wearing out the threads of the housing lens port and lenses over time: 

a.

 

Prior to installing the lens on the housing, it is recommended to apply a small 
amount of silicone grease on the threaded area of the lens (and adaptor, if used) 
to reduce the amount of friction. 

b.

 

Install the lens on the housing lens port underwater only and remove it prior to 
ending the dive. Once removed, the lens can be mounted on a lens holder. Avoid 
having the lens assembled on the housing on land as much as possible, as it is 
heavier and exerts more pressure on the threads. 

c.

 

It is recommended to reduce wearing of the threads by using lens mounting 
accessories such as bayonet mounts or flip adaptors. 

d.

 

These guidelines apply to all wet lenses brands and models, but especially 
important when making use of relatively heavy wet lenses. 

 

 

 

“Fantasea” warrants this Fantasea Line branded product against defects in materials and workmanship under 
reasonable use for a period of ONE (1) YEAR, (two years, where required by law as determined by the origin of 
the authorized dealer). This warranty is effective from the date of retail purchase from Fantasea or an authorized 
Fantasea dealer, by the original end‐user purchaser (“Warranty Period”). This warranty does not cover any 
commercial use of the product. If a product defect arises and a valid claim is received within the Warranty Period, 
at its option, Fantasea, or its authorized service facilities will either (1) repair the product defect at no charge, (2) 
exchange the product with a product that is new or which has been manufactured from new or serviceable used 
parts and is at least functionally equivalent to the original product. The warranty will not extend beyond the 
original warranty period. Your Fantasea Product should be registered within 30 days of purchase. You must keep 
the proof of purchase which indicates the date on which the purchase was made; as you may be required to show 
proof of purchase if you need warranty service. The following conditions apply: 1. This warranty extends to the 
original purchaser only. It is not assignable or transferable. 2. The warranty does not cover damage resulting from 
misuse, abuse, negligence, or accidents. Proper maintenance of the Product is the responsibility of the owner. 3. 
The warranty does not cover damage directly or indirectly resulting from the use of unauthorized replacement 
parts or service performed by unauthorized facilities. 4. This warranty does not cover any damage to any other 
product used in conjunction with the Fantasea product, including cameras and lenses, and resulting from any 
defect in the product materials or workmanship. 5. The cost of sending the product back to Fantasea or its 
authorized service facilities is the responsibility of the customer. 6. The warranty does not cover any incidental 
damages resulting from any defects in the product. This expressly includes any travel reimbursements or any 
other costs associated with the purchaser’s optional use of the product. The conditions of this warranty are 
expressly in lieu of all other expressed warranties, including the payment of consequential or incidental damages 
for the breach of any warranty. Please register your product on line at this URL: 

http://www.fantasea.com/registration

For further information, please visit our website 

www.fantasea.com 

or contact us at 

[email protected]

 

FANTASEA PRODUCT CONSUMER LIMITED WARRANTY 

Содержание 15355






































Отзывы: