background image

Two post hydraulic lift                                                                QJY3.0-E 

 

3

 

1  Safety 

1.1      Introduction 

Thoroughly read this manual before operating the lift and comply with the instructions. Always 
display the manual in a conspicuous location. 
Personal injury and property damage incurred due to non-compliance with these safety 
instructions are not covered by the product liability regulations. 

 

1.2      Symbols 

 

Failure to comply with instructions could result in personal injury 

 

Failure to comply with instructions could result in property damage 

 

Important information 

 

1.3      Intended Use 

The lift is designed for the safe lifting of automotive vehicles. Observe the rated load capacity 
and load distribution of the lift. 

 

Load distribution 

Front: Rear 

Load capacity 

Minimum 

Maximum 

QJY3.0-E 

3000kg 

2:3 

3:2 

 

In principle, the lift is designed for both 
approach directions. 
For a long service life, we recommend to use 
the short support arms for engaging the engine 
side of the vehicle. 

 

 

1.4      Safety Instructions for Commissioning 

  The lift may be installed and commissioned by authorized service personnel only. 
  The standard lift version may not be installed and commissioned in the vicinity of explosives 

or flammable liquids, outdoors or in moist rooms (e.g. car wash). 

Содержание QJY3.0-E




















Отзывы: