Fanbao QJY3.0-E Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 19

background image

Two post hydraulic lift QJY3.0-E

15

6.3.4 Lift stability

l

Every six months check the nuts of all anchor bolts for correct installation torque Tinst.

l

Retighten them as required.

Installation Torque Tinst

80Nm

6.4 Cleaning

Do not use high pressure/steam jet cleaners or caustic cleaning agents.
Risk of damage!

l

Periodically wash off aggressive substances and treat the lift with oil or wax spray.

l

Repair damage to the paintwork immediately to prevent corrosion. The RAL number is

available through the manufacturer.

«
...
13
14
15
16
17
...
»

Содержание QJY3.0-E




















Отзывы:

Нет отзывов

Похожие инструкции для QJY3.0-E

Бренд: RTRMAX Страницы: 14

SystemRoMedic EvaDrive450

Бренд: Handicare Страницы: 37

Бренд: Hall Research Technologies Страницы: 47

Бренд: ICP DAS USA Страницы: 6

Бренд: ADLINK Technology Страницы: 37

Бренд: HALDER Страницы: 2

ControlLogix 1756-CNB

Бренд: Allen-Bradley Страницы: 36

Бренд: Liko Страницы: 37

Бренд: Yeswelder Страницы: 8

Бренд: PLASMATECH Страницы: 58

Бренд: Victor Страницы: 168

ofs Fitel EZ-Terminator

Бренд: Furukawa Страницы: 28

Бренд: Sherman Страницы: 14

VIPER CUT 30Mk II

Бренд: Xcel-Arc Страницы: 24

Бренд: unicraft Страницы: 18

Бренд: MAHA Страницы: 28

Бренд: MANDREL welder Страницы: 36

XPASS B 330/1200 L

Бренд: BFT Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды