Fala STROKKUR-1, Руководство пользователя

Страница: 9 / 48

9
GB
O R I G I N A L I N S T R U C T I O N S
PRODUCT CHARACTERISTICS
Instantaneous water heater with battery provides access to hot, running water everywhere, where there is no other possibility
of water heating. Simply bring the running cold water, and due to the built-in electric heating element, you can get hot water.
Prior to working with the product, you should read all the instruction and keep it around.
For any damage caused by failure to comply with safety regulations and instructions of this manual, the supplier is not respon-
sible.
EQUIPMENT
The product is supplied in a complete state but it requires the installation steps, which are described later in this manual. With the
product, there is supplied a battery spout and water connection.
SAFETY INSTRUCTIONS
Attention! The product is characterized by high power consumption. Before connecting the product to mains, you should make
sure, that the mains parameters will be sufficient to supply the product.
Before connecting the product to mains, you should make sure that voltage, the frequency and the performance of the mains
correspond to the values on the rating plate of the product. Power cable plug must fit into the mains socket. It is forbidden to alter
the plug.
The product must be connected directly to a single wall mains socket. it is forbidden to use extension cables, splitters, and double
sockets. Circuit power supply network must be equipped with a grounding conductor and protection for 16 A.
Avoid contact of the power cable with sharp edges and hot objects and surfaces. When the product is working, the power cable
must always be fully unwinding, and its location should be set so, it would be no obstacle during the operation of the product.
Placing the power cable can cause a tripping hazard. The power outlet should be located in such a place, that there would be
always possible to quickly disconnect the power cable plug.
The socket should be located possibly far away from water outlet.
When disconnecting the power cable plug, you should always pull by the plug housing, never by the cable.
If the power cable or plug are damaged, you should immediately disconnect them from the mains and contact authorized service
of the manufacturer for replacement. Do not use the product with a damaged cable or plug. The power cable or plug can not be
repaired, in the event of a failure of these elements they should be replaced with new ones, free from defects.
Before connecting the product to mains, you should make sure, that the water pressure is within the range specified in the table
technical data and on the rating plate of the product.
It is recommended that the product connection to the water supply will be performed by a qualified personnel.
The product designed for only an indoors installation. The product should be not mounted at places, where the temperature will fall
to the level which would cause freezing of water. Frozen water increases its volume, which can lead to a damage of the product.
If you noticed any damage to the product, it is prohibited to use it. All damage must be removed before resuming use of the product.
PRODUCT ASSEMBLY
Attention! The first step should be the connection of the product to the water source, and checking the tightness of the water
connections, and only then the product should be connected to an electrical power supply. It is forbidden to mount the product,
which is connected to mains.
Attention! The product designed only for a vertical installation. It is forbidden to mount the product in any different position.
In the first place, you should mount to the heater body a drain sprout. To do this, you should check whether all gaskets and the
resistance ring are located in the cavings of the spout mounting (II). Then, without a usage of any tools, you should screw a fixing
collar on the threaded body of the heater (III).
Correctly attached drain spout should smoothly rotate in the range of 360 degrees, with slightly a perceptible resistance.
The heater body should be mounted in the hole near the sink, of the wash basin so that water may have no obstacles to get to
the drain plumbing. Place a rubber pad under the body, which will protect the mounting place from damage. Fasten the heater
body by screwing the fixing nut (IV). It is recommended to tighten the fixing nut without the use of any tools, however, if it does not
provide a stable body mounting of the heater, you can use the wrench to tighten. You should be careful when tightening the nut