![background image](http://html1.mh-extra.com/html/faac/estate-swing-e-sl-1800/estate-swing-e-sl-1800_installation-manual_3119326002.webp)
CE DECLARATION OF CONFORMITY FOR MACHINES
(DIRECTIVE 2006/42/EC)
Manufacturer:
FAAC S.p.A.
Address:
Via Calari, 10
-
40069 Zola Predosa BOLOGNA
-
ITALY
Declares that:
Operator mod. C720
-
C721
is built to be integrated into a machine or to be assembled with other machinery to create a machine under the provisions of
Directive 98/37/EC;
conforms to the essential safety requirements of the following EEC directives:
2006/95/EC Low Voltage Directive
2004/108/EC Electromagnetic Compatibility Directive
and also declares that it is prohibited to put into service the machinery until the machine in which it will be
integrated or of which it will become a component has been identified and declared as conforming to the
conditions of Directive 2006/42/EEC and subsequent amendments.
Bologna, 01
-
12
-
2010
The Managing Director
A. Marcellan
1) ATTENTION! To ensure the safety of people, it is important
that you read all the following instructions. Incorrect installation
or incorrect use of the product could cause serious harm to
people.
2) Carefully read the instructions before beginning to install the prod-
uct.
3) Do not leave packing materials (plastic, polystyrene, etc.) within
reach of children as such materials are potential sources of danger.
4) Store these instructions for future reference.
5) This product was designed and built strictly for the use indicated
in this documentation. Any other use, not expressly indicated here,
could compromise the good condition/operation of the product and/or
be a source of danger.
6) FAAC declines all liability caused by improper use or use other
than that for which the automated system was intended.
7) Do not install the equipment in an explosive atmosphere: the
presence of inflammable gas or fumes is a serious danger to safety.
8) The mechanical parts must conform to the provisions of Stand-
ards EN 12604 and EN 12605.
For non
-
EU countries, to obtain an adequate level of safety, the
Standards mentioned above must be observed, in addition to nation-
al legal regulations.
9) FAAC is not responsible for failure to observe Good Technique in
the construction of the closing elements to be motorized, or for any
deformation that may occur during use.
10) The installation must conform to Standards EN 12453 and EN
12445.
For non
-
EU countries, to obtain an adequate level of safety, the
Standards mentioned above must be observed, in addition to nation-
al legal regulations.
11) Before attempting any job on the system, cut out electrical pow-
er. 12) The mains power supply of the automated system must be
fitted with an all
-
pole switch with contact opening distance of 1/8 in.
or greater. Use of a 6A thermal breaker with all
-
pole circuit break is
recommended.
13) Make sure that a differential switch with threshold of 0.03 A is
fitted upstream of the system.
14) Make sure that the earthing system is perfectly constructed and
connect metal parts of the closure to it.
15) The automated system is supplied with an intrinsic anti
-
crushing
safety device consisting of a torque control. Nevertheless, its tripping
threshold must be checked as specified in the Standards indicated at
point 10.
16) The safety devices (EN 12978 standard) protect any danger
areas against mechanical movement Risks, such as crushing, drag-
ging, and shearing.
17) Use of at least one indicator
-
light (e.g. FAACLIGHT ) is recom-
mended for every system, as well as a warning sign adequately se-
cured to the frame structure, in addition to the devices mentioned at
point “16”.
18) FAAC declines all liability as concerns safety and efficient opera-
tion of the automated system, if system components not produced by
FAAC are used.
19) For maintenance, strictly use original parts by FAAC.
20) Do not in any way modify the components of the automated sys-
tem.
21) The installer shall supply all information concerning manual op-
eration of the system in case of an emergency and shall hand over to
the user the warnings handbook supplied with the product.
22) Do not allow children or adults to stay near the product while it is
operating.
23) Keep remote controls or other pulse generators away from chil-
dren, to prevent the automated system from being activated involun-
tarily.
24) Transit is permitted only when the automated system is idle.
25) The user must not attempt any kind of repair or direct action
whatever and contact qualified personnel only.
26) Check at least every 6 months the efficiency of the system, par-
ticularly the efficiency of the safety devices (including, where fore-
seen, the operator thrust force) and of the release devices.
27) Anything not expressly specified in these instructions is not
permitted.
WARNINGS FOR THE INSTALLER
GENERAL SAFETY OBLIGATIONS
1
Содержание Estate Swing E-SL 1800
Страница 1: ...E SL 1800...