FAAC Estate Swing E-S 1100 Series Скачать руководство пользователя страница 53

Страница: 53 / 53

Photo Eye, Safety Edge, Safety Loop:

Normally Closed (NC) of safety device

= #5 ter minal on gate opener control board.

Common (COM) or Ground (GND) of safety device

= #14 ter minal on gate opener control

board.

12V Power positive (+) or (12V) or (PWR) of safety device

= #11 ter minal on gate opener

control board.

12V Power Negative (

) or (GND) or (PWR) of safety device

= #12 ter minal on gate opener

control board.

*Remove safety jumper from #5 terminal if using a safety device.

Solenoid Gate Lock:

Terminal 1 of lock control board

= #7 ter minal on gate opener cir cuit board

Terminal 2 of lock control board

= Negative battery lead of gate opener battery

Terminal 3 of lock control board

= Negative (black) lead of gate lock

Terminal 4 of lock control board

= Positive lead of gate lock

Terminal 5 of lock control board

= Positive battery lead of gate opener battery

Magnetic Gate Lock: Magnetic gate locks must have their own power supply and their own
relay.

Coil of relay for magnetic lock

= #7 ter minal on gate opener control board.

Coil of relay for magnetic lock

= #12 ter minal on gate opener control board.

Connect positive lead of the power supply directly to the positive lead of the mag lock.

Connect negative lead of the power supply to the N/C terminal of the relay.

Connect the COM terminal of the relay to the negative lead of the mag lock.

Accessories Wiring

9.6

Estate Swing

Содержание Estate Swing E-S 1100 Series






















































Результаты поиска

Содержание Estate Swing E-S 1100 Series

Отзывы:

Бренды по названию

Популярные бренды

FAAC Estate Swing E-S 1100 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Estate Swing E-S 1100 Series

Отзывы:

Бренды по названию

Популярные бренды