background image

ATTENTION:

• 

The installation must always be in accordance with the applicable provisions of National 
Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical Code part 1, 
section 16.

• 

Cette installation doit toujours être conforme aux dispositions applicables du Code 
américain de l’électricité (National Electrical Code) ANSI/NFPA 70, article 725, et du Code 
canadien de l’électricité, partie 1, section 16.

• 

The power supply shall not be permanently fixed to building structure or similar structure.

• 

La source d’alimentation ne devra pas être fixée de façon permanente à une structure de 
bâtiment ou à d’autres structures similaires.

• 

Power over Ethernet (PoE) is intended for indoor use only. It is to be connected only to 
networks or circuits that are not routed to the outside plant or building.

• 

L’alimentation via Ethernet (PoE) est destinée à une utilisation en intérieur uniquement. 
Elle doit être connectée seulement à des réseaux ou des circuits qui ne sont pas routés 
au réseau ou au bâtiment extérieur.

• 

The touchpanels are intended for connection to a Power over Ethernet circuit for 
intra-building use only and are considered to be part of a Network Environment 0 per 
IEC TR62101.

• 

Les écrans tactiles sont conçus pour une connexion à un circuit PoE pour une utilisation 
intérieure uniquement et sont considérés comme faisant partie d’un environnement 
réseau 0 selon la norme IEC TR62101.

• 

Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling 
spaces or in wall cavities. The power supply is to be located within the same vicinity as 
the Extron AV processing equipment in an ordinary location, Pollution Degree 2, secured 
to the equipment rack within the dedicated closet, podium, or desk.

• 

Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une 
utilisation dans les espaces d’aération ou dans les cavités murales. La source 
d’alimentation doit être située à proximité de l’équipement de traitement audiovisuel 
dans un endroit ordinaire, avec un degré 2 de pollution, fixé à un équipement de rack à 
l’intérieur d’un placard, d’une estrade, ou d’un bureau.

• 

Always use a power supply provided by or specified by Extron. Use of an unauthorized 
power supply voids all regulatory compliance certification and may cause damage to the 
supply and the end product.

• 

Utilisez toujours une source d’alimentation fournie ou recommandée par Extron. 
L’utilisation d’une source d’alimentation non autorisée annule toute conformité 
réglementaire et peut endommager la source d’alimentation ainsi que le produit final.

• 

If these products are not provided with a power supply, they are intended to be supplied 
by a UL Listed power source marked “Class 2” or “LPS” and output rated 48 VDC or 
56 VDC (PoE), minimum 0.35 A, or UL Listed Extron XTP/DTP remote power source.

• 

Si ces produits ne sont pas fournis avec une source d’alimentation, ils doivent être 
utilisés avec une source d’alimentation certifiée UL de classe 2 ou LPS avec une tension 
nominale 48 Vcc ou 56 Vcc (PoE), 0,35 A minimum, ou une source d’alimentation à 
distance XTP/DTP Extron certifiée UL.

• 

Extron power supplies are certified to UL/CSA 60950-1 and are classified as LPS 
(Limited Power Source). Use of a non-LPS or unlisted power supply will void all regulatory 
compliance certification.

• 

Les sources d’alimentation Extron sont qualifiées UL/CSA 60950-1 et sont 
classées LPS (Limited Power Source). L’utilisation d’une source d’alimentation non-listée 
ou non-listée LPS annulera toute certification de conformité réglementaire.

Attention

mise en garde

 

TLP Pro 525, 725, and 1025 Series Touchpanels • Panel Features

10

Содержание TouchLink Pro













































Отзывы: