Extron electronics MultiMatrix SMX System Скачать руководство пользователя страница 37

Страница: 37 / 48

SMX System MultiMatrix Switcher • SIS Programming Guide

Command

ASCII Command

(host to switcher)

Response

(switcher to host)

Additional Description

IP Setup Commands (Continued)

Set verbose mode

X3&

}

Vrb

X3&

]

Enable or disable verbose mode

or tagged responses, in which

additional information is given in

query response.

NOTE:

The SMX can send out unsolicited information (such as a notice of a change in input or some other setting). This is a

verbose (wordy) relationship between the switcher and a connected device. For a direct RS-232 or RS-422 connection,

the SMX is set for verbose mode by default. When the SMX is connected via Ethernet, verbose mode is disabled by

default to reduce the amount of communication traffic on the network. If you want to use verbose mode with a

switcher connected via Ethernet, you must set this mode to On each time you reconnect to the SMX.

iew verbose mode

}

X3&

]

Show verbose mode or tagged

response status

X3&

Reset Commands

Reset switcher

ZXXX

}

Zpx

]

Clears all ties and presets, audio

gain and volume, and resets unit to

factory default.

NOTE:

Excludes IP settings, such as IP address, subnet mask, and gateway address. Does not remove file system.

Absolute system reset

ZQQQ

}

Zpq

]

Clears all ties and presets, and resets

unit to factory default

(mode 5 reset).

NOTE:

Includes resetting IP address to 192.168.254.254 and subnet mask to 255.255.0.0. Firmware version remains the same.

NOTES:

X3&

= V

erbose mode:

= neither verbose mode nor tagged response enabled;

= verbose enabled, no tagged

responses (default);

= tagged responses enabled, verbose mode disabled;

= verbose mode and tagged responses

enabled

Содержание MultiMatrix SMX System

















































Результаты поиска

Содержание MultiMatrix SMX System

Отзывы:

Похожие инструкции для MultiMatrix SMX System

Бренды по названию

Популярные бренды

Extron electronics MultiMatrix SMX System, Руководство по установке

Результаты поиска

Содержание MultiMatrix SMX System

Отзывы:

Похожие инструкции для MultiMatrix SMX System

Бренды по названию

Популярные бренды