Extron electronics MultiMatrix SMX System Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 48

background image

4

SMX System MultiMatrix Switcher • Installation

The Ethernet connection indicator LEDs marked "Link" and "Act"
indicate the status of the SMX Ethernet connection. The Link LED
lights green when connected to an Ethernet LAN, and the Act LED
flickers amber, as the devices communicate.

NOTE:

Do not use standard telephone cables, as they do not

support Ethernet or fast Ethernet. Do not stretch or bend
cables as transmission errors could occur.

Remote port

—

For serial RS-232 or RS-422 control, connect a host

computer or control system through this 9-pin D connector. RS-232
protocol (default values):

•

9600 baud

•

1 stop bit

•

no parity

•

8 data
bits

•

no flow
control

NOTE:

See the

SMX User Guide

for more details.

Connecting Power

Plug in a standard IEC power cord from a 100 to 240 VAC, 50-60 Hz
power source into the rear panel.

Setting Plane Addresses

Set the plane address (0-15) of each I/O board with the
16 position (0-F) rotary encoder. Each board can be set
to any plane address, including multiple boards to the
same address.

Installing Additional I/O Boards

The I/O boards used in any installation will vary and can be installed
and changed as desired.

NOTE:

All boards are hot-swapable and can be installed without

shutting down the SMX or removing the power.

See

Installing New Boards

on page 38 to reconfigure or populate the

SMX frame.

Wiring Audio Connectors

Audio input connectors

—

Connect audio input devices to the

3.5 mm, 5-pole captive screw connectors (up to two groups of eight
sets possible). Wire the input connector for the appropriate signal
type (see

Do not tin the wires!

ADDRESS

«
...
8
9
10
11
12
...
»

Содержание MultiMatrix SMX System

















































Отзывы:

Нет отзывов

Похожие инструкции для MultiMatrix SMX System

Бренд: Magnetrol Страницы: 28

OmniView Secure F1DN102Uea

Бренд: Belkin Страницы: 36

LMP-1204G-SFP Series

Бренд: ANTAIRA Страницы: 20

Бренд: Sarowin Страницы: 9

EdgeLens INT10G8SR56

Бренд: Garland Страницы: 76

T0-4 SE2 Series

Бренд: Eaton Страницы: 2

Бренд: SELS Страницы: 2

Бренд: PhD Solutions Страницы: 23

ProSAFE JGS516PE

Бренд: NETGEAR Страницы: 2

Бренд: GarrettCom Страницы: 76

Бренд: Davey Страницы: 2

Бренд: Flamingo Страницы: 2

Ethernet Switch Boards

Бренд: Intel Страницы: 52

Бренд: KanexPro Страницы: 35

Бренд: C&C TECHNIC Страницы: 2

Бренд: KinAn Страницы: 5

JTECH-4K88-EX-RX

Бренд: J-TECH Страницы: 40

Бренд: Samson Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды