38
SMX System MultiMatrix Switcher • Reference Material
Mounting the SMX
Use two screws on each side of the
SMX to attach the front panel to a
rack. See the
SMX User Guide
for
other mounting considerations
(
Installing New Boards
NOTE:
All boards are hot-swappable, and can be installed
without shutting down the SMX or removing the power.
1.
Take note of how many slots your board needs to occupy.
a.
If necessary, remove as many blank panels as needed.
b.
If the new board is replacing an existing board, remove all
cables from the currently installed one and loosen the two
outer screws to remove the board.
2.
Slide the I/O board into the open slot, carefully aligning it with
the plastic slides and the power source in the frame. Push it firmly
into place.
3.
Tighten the screws on each end of the board.
NOTE:
Use a tool to fully tighten the screws after initial
installation and subsequent removal and replacement
of the boards.
4.
Set the plane address with the rotary encoder (see
on page 4).
RESET
RS
232
/RS
422
REMO
TE
LA
N
AC
T
LINK
50-
60H
z
100
-24
0V
1.3
A M
AX
.
US
LIS
TED
17
TT
AU
DIO
/VID
EO
AP
PAR
ATU
S
®
1
5
tx rx
tx
3
tx rx
7
tx
2
6
tx rx
tx
4
tx rx
8
tx
PL
AN
E A
DR
ES
S
DIGI
TAL
VID
EO
SDI /
HDSD
I OUTP
UT
S
8
7
1
4
5
6
3
2
SDI /
HDSD
I IN
PUTS
8
7
1
4
5
6
3
2
PL
AN
E A
DR
ES
S
INPUT
S
1
2
3
4
OUTPUT
S
1
2
3
4
PL
AN
E A
DR
ES
S
COMPUTER
IN
5
6
7
8
1
2
3
4
COMPUTE
R OU
T
5
6
7
8
1
2
3
4
PL
AN
E A
DR
ES
S
VIDEO
OUTPU
TS
16
15
9
12
13
14
11
10
VIDEO I
NPUTS
16
15
9
12
13
14
11
10
16
15
9
12
13
14
11
10
16
15
9
12
13
14
11
10
S-VIDE
O
Y
C
Y
C
Y
C
IN
PL
AN
E A
DR
ES
S
9
10
11
12
13
14
15
16
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
1
R
L
2
R
L
3
R
L
4
R
L
5
R
L
6
R
L
7
R
L
8
R
I
N
P
U
T
S
I
N
P
U
T
S
9
10
11
12
13
14
15
16
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
1
R
L
2
R
L
3
R
L
4
R
L
5
R
L
6
R
L
7
R
L
8
R
O
U
T
P
U
T
S
O
U
T
P
U
T
S
Optional
Board
(audio shown)
Figure 30.
SMX Frame Rear Showing Board Installation
New output boards are autodetected and take approximately
20 seconds to initialize. If the unit is connected by RS-232 or RS-422,
Telnet, or LAN, a
Reconfig
notice is shown.
Any new boards are now ready for cabling and configuration.
Содержание MultiMatrix SMX System
Страница 1: ...Setup Guide 68 1452 50 Rev B 10 11 SMX System MultiMatrix Switcher Matrix Switcher ...
Страница 6: ...vi SMX System MultiMatrix Switcher Contents ...
Страница 45: ...39 SMX System MultiMatrix Switcher Reference Material Notes ...
Страница 46: ...40 SMX System MultiMatrix Switcher Reference Material ...
