Extron electronics MultiMatrix SMX System Скачать руководство пользователя страница 32

Страница: 32 / 48

SMX System MultiMatrix Switcher • SIS Programming Guide

Command

ASCII Command

(host to switcher)

Response

(switcher to host)

Additional Description

Information Requests

NOTE:

Firmware version, part number

, and information are for the primary frame only

Query firmware version

X2!]

Example:

1.14

]

Ver01*

X2!

]

erbose mode 2 or 3

Query system status

X2$

•

X2$

•

X2$

•

X2%

•

X2^

•

X7&

•

X7*]

Example:

Sts0*3.31 4.98 24.22 +100.40 03305 03308 1 0

]

erbose mode 2 or 3)

3.31

and

4.98

are power supply voltages;

24.22

is fan voltage,

100.40

(degrees F) is temperature,

03305

is fan 1 rpm,

03308

is fan 2

rpm,

is primary power supply (OK).

Query Switcher Information per

plane (16 actual and 10 virtual)

plus board configuration

•

...

•

...

]

V16x16A16x16

•

...

]

NOTE:

The

response gives 26 parameters, the first 16 (V_x_A_x_) are plane information (planes 0-15), and the next are

virtual planes 1 - 10 (

Query plane address per slot

STAT

}

X2@

(slot 1)

•

X2@

(slot 2)

•

...

X2@

(slot 6/8/10)

]

Stat

X2@

(slot 1)

•

X2@

(slot 2)

•

...

X2@

(slot 6/8/10)

]

Slot 1

Example:

Stat* 00

•

]

(5U frame, 10 slots)

indicates no boar

d is installed

NOTES:

= Input number

- <

maximum num

ber of inputs

= untied

= Output number

- <

maximum number of

outputs

X2!

= Firmware version number

x.xx

X2@

= Plane number

X2^

= Fan speed (rpm)

X2$

= V

oltage (

voltage)

X7&

= Primary power supply

= not installed,

= OK

X2%

= T

emperature

X7*

= Secondary (redundant) power supply

= not installed,

= OK

Содержание MultiMatrix SMX System

















































Результаты поиска

Содержание MultiMatrix SMX System

Отзывы:

Похожие инструкции для MultiMatrix SMX System

Бренды по названию

Популярные бренды

Extron electronics MultiMatrix SMX System, Руководство по установке

Результаты поиска

Содержание MultiMatrix SMX System

Отзывы:

Похожие инструкции для MultiMatrix SMX System

Бренды по названию

Популярные бренды