Extron electronics IPL Pro CR88, Руководство пользователя

Страница: 25 / 43

IPL Pro Series • Hardware Features and Installation 17
C
LAN/PoE (Ethernet) connectors and LEDs — To connect the IPL to an Ethernet
network (so you can configure and control the IPL and the devices connected to it),
plug a cable into the LAN RJ-45 socket (see figure 7, on page 13) and connect the
other end of the cable to a network switch, hub, router, or PC connected to a LAN or
the Internet. For details of communication protocols, ports, and services used, see the
Pro Series Control Product Network Ports and Licenses Guide at www.extron.com .
The IPL Pro Series control processors accept power over Ethernet (PoE) through the
LAN port (see the
Power over Ethernet (PoE) Attention statement
on page 15).
Both an external power supply and PoE can be connected to the control processor
simultaneously. The IPL uses PoE when it is available but can switch seamlessly to the
external power supply if the PoE connection is dropped.
Cabling:
•
For 10Base-T (10 Mbps) networks, use a CAT 3 or better cable.
•
For 100Base-T (max. 155 Mbps) or 1000Base-T networks, use a CAT 5 or better cable.
You must configure this port before using it. Configure the settings via Global
Configurator. See
Software-Based Configuration and Control starting on
page 24 of this guide for basic information on configuration.
Activity LED (connector and front panel) — This yellow LED blinks to indicate network
activity.
Link LED (connector and front panel) — This green LED lights to indicate a good
network connection.
1000 LED (front panel) — This green LED lights when the unit is connected to a gigabit
network connection.
1000
LINK
ACT
LAN / PoE
I IPL PR PR O S 6
5-A6- XX-XX-XX
### E######
5-A6-XX-XX-XX
Rear Panel Front Panel
RJ-45
Connector
Insert Twisted
Pair Wires
Pins:
1 2 3 4 5 6 7 8
1000 Mbps
Connection
Network is
active.
Data is being
sent/received.
Link
LED Activity
LED
LAN/PoE (Ethernet)
Default protocol:
• IPL IP address: 192.168.254.
250
• Gateway IP address: 0.0.0.0
• Subnet mask: 255.255.255.0
• DNS address: 127.0.0.1
• DHCP: off
• Link speed and duplex level:
autodetected
• Data rates: 10/100/1000Base-T
Power over Ethernet (PoE):
If PoE is available, the IPL uses PoE.
If PoE is dropped (disconnects), the
IPL switches seamlessly to the
external 12 VDC power supply, if it
is installed.
Default login credentials:
• Username:
admin
• Password: extron
Ethernet
PC
Touchlink Pro
Touchpanel
Extron Devices
(Switchers, Scalers)
TCP/IP
Network
Figure 10. LAN Connector and LEDs
D
MAC address — This is the unique user hardware ID number
(Media Access Control [MAC] address) of the unit (for example,
00-05-A6-05-1C-A0). You may need this address during
configuration.
The following addresses apply to control
processors.
For single NIC models...
192.168.254.250 = primary/public NIC
TouchLink Touchpanels will have
the following default IP address:
192.168.254.251
NOTE: DHCP is off by default.
Keep the “IPL LAN port
defaults” text set to “no
color” (to use as an invisible
text/hyperlink marker).
MAC: 00-05-A6- XX-XX-XX
S/N: ####### E######
MAC
Address