2
HC 403 EU, HC 403 MK • Setup Guide (Continued)
HDMI IN
PWR HDCP HDMI VGA AUTO
VGA IN
DTP T EU 232
AUDIO IN
AUDIO IN
Tx Rx G
RS-232
OVER TP
Tx Rx G
RS-232
POWER
REMOTE
12V
A MAX
OU
T
SIG
LINK
HCT 102
Front
Rear
POWER
12V
2.0
A MAX
INPUTS
OUTPUTS
1
TP
HDMI
L
R
AUDIO
HDMI/CEC
SIG
LINK
IN
COM
IR
DIGITAL I/O
1 2
S G
Tx Rx G
G 3 4 G
HCR 102
LAN
Ethernet
PC with
GlobalViewer
Enterprise
ShareLink 200 N
AUDIO
OUT
LAN / PoE
VGA OUT
HDMI OUT
USB 3
POWER
5V
2.3A MAX
RESET
A/PoE
B
POWER
12V
1.7A MAX
HDMI
HDMI
Tx Rx G
RS-232
COM
L
AUDIO
R
OUTPUT
1
C T
2
C T
3
C T
4
C T G +V
CONTACT / TALLY
LAN
INPUT
OUTPUT
TCP/IP
Network
HCR 102
Scaling Receiver
Display
Extron
ShareLink Pro 1000
Wireless and Wired
CollaborationGateway
HDMI
HDMI
RS-232
Twisted Pair
Cable (AV)
230'
HDMI
Audio
Ethernet
MODEL 80
FLAT PANEL
HCT 102 EU/MK
Wall Plate Transmitter
Extron
OCS 100W
Wall Mount
Occupancy
Sensor
Ethernet
Room
Wireless Access
Point
Tablet
TCP/IP
Network
VGA
Audio
Figure 1.
An HC 403 EU or HC 403 MK System Application
Panels and Features
Front and Side Panel Features
CONFIG
HCR 102
1
INPUT
LPCM-2CH
MULTI-CH
HDCP
SIGNAL
R
MENU
ENTER
HOLD FOR 720p/1080p
1
AUDIO
HDMI IN
PWR HDCP HDMI VGA AUTO
VGA IN
HCT 102 MK
AUDIO IN
AUDIO IN
RESET
SERVICE
HCR 102
A
I J
B
C
D
H
FG
E
HCT 102 MK Front
HCT 102 MK Side
D
K
I
L
C
Input
3
Input
2
Figure 2.
HCT 102 MK Front Panel (Top), HCR 102 Front Panel (Bottom),
A
Configuration (Config) connector
(USB mini-B), page 13
I
Power LED (HCT 102 EU/MK), power and reset indicator
LED (HCR 102) (see below)
B
Input selection button and LED
, page 16
J
Reset button
(see below and page 17)
C
Input signal presence (Signal) LEDs
, page 16
K
Auto Switch LED (see below)
D
Input HDCP status LED
, page 16
L
Service connector (for use by Extron support staff)
E
Audio input type LEDs
(LPCM-2Ch and Multi-Ch, page 16
F
Menu
button,
G
Enter
button, and
H
Navigation (
right
,
left
,
up
, and
down
arrow)
buttons (see
To configure the AV settings using the OSD
and front panel buttons:
on page 9)
J
Reset button
(HCR 102) — Pressing this recessed button causes various product settings to be reset to the factory defaults
(see
Reset Modes: a Brief Summary
on page 17).
I
Reset and power LED
— This green LED indicates either the power status of the transmitter or the receiver, or the reset
mode of the receiver. LED indications are as follows:
HCT 102 EU/MK Transmitter
HCR 102 Receiver
•
Off
— The unit is not powered on.
•
On, lit green
— The unit is
powered on.
•
Off
— The unit is not powered on.
•
On, lit steadily
— The unit is powered on.
•
Blinking
— The unit is powering up or the HCR 102 is performing a reset.
The blink pattern depends on the selected reset mode.
For full descriptions of reset modes, how to use the reset button to activate them,
and details of LED indications of each mode, see the
HC 400 Series User Guide
.
K
Auto Switch LED
— This LED on the transmitter lights green if either of the auto-switching modes is enabled, and it turns off
if both of the auto-switch modes are disabled. For details on auto-switching modes, see the
HC 400 Series User Guide.
NOTES:
• The EU and MK transmitters are identical except for
faceplate size and mounting hardware. They have the
same connectors, LEDs, and capabilities.
• For AV connectors on the HCT 102 EU/MK, see
Rear,
Side, and Front Panel Features
on page 4.
Need to make a note in the UG of how this LED
on the EU/MK models behaves differently from
the LED on the D model! There is no amber
mode and this doesn’t indicate an active signal.
