Extron electronics HC 403 EU Скачать руководство пользователя страница 13

13

AV Outputs

1. 

Connect a display, projector, or other AV device to the Outputs HDMI/CEC connector (see figure 3, 

G

 on page 4) on the 

receiver rear panel for HDMI AV output. 

2. 

Connect the cable and install the LockIt bracket (see step 2 within 

Digital AV input

 on the previous page  ) in the same 

method as for the HDMI inputs.

3. 

For analog audio output, connect an amplifier,  
powered speaker or other audio device to the 
3.5 mm, 5-pole captive screw connector. See the 
diagrams at right for the appropriate wiring for your 
application. For unbalanced audio, connect the 
sleeve(s) to the ground contact; do not connect 
the sleeve(s) to the negative (-) contacts.

Control

USB connections

Connect a host computer to the USB mini-B port on the receiver (see figure 3, 

A

 on page 3) for AV configuration.

Receiver connections for display or device control

The serial, IR, digital I/O, LAN, and CEC ports can all be used for device control. All of these ports must be configured using 
Global Configurator 

Serial

For serial control using RS-232, connect the serial control port of  
the AV device to the COM port (see figure 3, 

K

 on page 4) 

of the HCR 102 receiver as shown below.

COM

Tx Rx G

NOTE:

  If you use a cable that has a drain wire, 

tie the drain wire to ground at both ends.

Strip wires 3/16" (5 mm) max.

RS-232- 

Controllable 

Device

Transmit

Receive

Receive (Rx)

Transmit (Tx)

Ground

Rx

G

Tx

Select protocol via software.

COM port default protocol:

• 9600 baud

• 8 data bits

• no parity

• 1 stop bit

• no flow control

NOTE:

  The COM port supports 

software flow control only.

Serial (COM) Port 

(RS-232)

Heat Shrink

HCR 102

Rear 

Panel

Infrared

For IR control of AV equipment, connect one or two  
IR emitters to the IR port (

L

) of the HCR 102 receiver 

as shown below.

IR

S G

S

G

(-)

(+)

(-)

(+)

(+)

(-)

To the 

IR Receiver 

of a 

Projector, 

Display, or 

Other 

Device

Two Single IR Emitters

Ground

IR Output Signal

Unidirectional

IR

IR Port

IR (30 kHz to 300 kHz, 

with or without carrier signals)

HCR 102

Rear 

Panel

LR

LR

Balanced Audio Output

Tip

Ring

Tip

Ring

Sleeves

Unbalanced Audio Output

Tip

No Ground Here

Tip

Sleeves

No Ground Here

Содержание HC 403 EU



















Отзывы: