background image

2                                     382860       Ver. 1.5    2/01

 

2. SPECIFICATIONS 

2.1 General Specifications 

Display 

One Main and three Sub 3-3/4-digit (3999 count) LCDs plus 40-

segment bargraph

 

Max. Input 

Current 

DC/AC : 20A

 

Operating 

Conditions 

0 to 104

o

F (0 to 40

°

C), relative humidity: <75%, not wetting 

 

Storage 

Conditions 

0 to 122

o

F (-10 to 50

°

C), relative humidity: <76%, not wetting

 

Power 

9V Battery: NEDA 1604 9 V or 6F22 

 

Dimensions 

7.36x3.3x1.34” (187x84x34mm)

 

Weight 

9.8oz (305g)

 

 

2.2 Range Specifications 

NOTES:

 Accuracies are % of reading and specified at 23

o

C with RH <75% 

for a period of 1 year after production. Warm-up time is 1 minute. 

    Mode 

Measuring Range 

Accuracy 

Resolution 

400 mV 

100 

µ

4 V 

1 mV 

40 V 

10 mV 

400 V 

± (0.3% + 1dgt) 

100 mV 

DC Voltage 

1000 V 

± (0.5% + 1dgt) 

1 V 

400 

µ

0.1

µ

4mA 

± (1.0% + 1dgt) 

µ

40mA 

10 

µ

400mA 

± (0.8% + 1dgt) 

100

µ

4A 

1mA 

DC Current 

20A 

± (1.5% + 5dgt) 

10mA 

 

                     Accuracy 

    Mode 

Measuring Range 

40Hz-1KHz 

1KHz–10KHz 

Resolution 

400 mV 

0.1mV 

4 V 

1mV 

40 V 

10mV 

400 V(<200V) 

± (0.8%+3dgts)  ± (2.5%+5dgts) 

100mV 

400V(<400V) 

100mV 

AC Voltage 

750 V 

± (1.0%+3dgts) 

N/A 

1V 

400 

µ

0.1

µ

4mA 

1

µ

40mA 

10

µ

400mA 

± (2.5%+5dgts) 

100

µ

4A 

± (1.5%+3dgts) 

1mA 

AC Current 

20A 

± (2.0%+5dgts) 

N/A 

10mA 

 

 

 

Содержание 382860

















Отзывы: