Evinrude E-TEC 115 Скачать руководство пользователя страница 43

Страница: 43 / 90

TRANSPORTING THE OUTBOARD

TRAILERING

Trailering Bracket

The outboard is designed to be trailered in a

vertical position or tilted, using the trailering

bracket. Use the position best suited for your

boat.

To engage bracket —

Tilt the outboard fully

using the tilt switch inside the boat or the

trailering tilt switch (on port or starboard side

of engine, depending on configuration).

Pull down the trailering bracket. A detent will

hold the bracket in position.

Lower the outboard until the trailering bracket

locks into place in the stern brackets (see “B”

below).

WARNING

Keep everyone clear of stern area when

raising or lowering the outboard. Per-

sonal injury or death can result from

contact with moving parts of the out-

board.

1. Trailering tilt switch
2. Tilt switch inside boat

DR3964

DRC4014

DR5081

DR5073

Содержание E-TEC 115



























































































Результаты поиска

Содержание E-TEC 115

Отзывы:

Похожие инструкции для E-TEC 115

Бренды по названию

Популярные бренды

Evinrude E-TEC 115, Оригинальное руководство пользователя

Результаты поиска

Содержание E-TEC 115

Отзывы:

Похожие инструкции для E-TEC 115

Бренды по названию

Популярные бренды