Evinrude E-TEC 115 Скачать руководство пользователя страница 64

Страница: 64 / 90

Product Information

20 Inch 90–130 HP V4 Models —

Install pro-

peller nut and tighten to a torque of 120-144

in. lbs. (13.6-16.3 N·m).

25 inch 90–130 HP V4 Models and

All 135–300 HP V6 Models —

Install propeller

nut and tighten to a torque of 70 to 80 ft. lbs.

(95 to 109 N·m). Install keeper on propeller

nut, align keeper slots and cotter pin hole.

IMPORTANT:

If cotter pin holes in the propel-

ler nut and propeller shaft are not aligned,

tighten the nut until they are in line. Do not

loosen.
Install new cotter pin and bend ends to se-

cure.
Remove block of wood. Make sure engine is

in NEUTRAL; give propeller a spin. It must

turn freely.

Repair

If your propeller hits a solid object, the impact

is partially absorbed by the bushing in the hub

to help prevent damage to the outboard. A

strong impact can damage the hub and pro-

peller blades. Damage to blades can cause

unusual and excessive vibration. Damage to

the hub can cause excessive engine RPM

with little forward movement.

Avoid or limit operation using

a damaged propeller. Carry a spare pro-

peller.

Keep your propeller in good condition. Use a

file to smooth slight damage to blade edges.

See your Dealer for repair of serious damage.

NOTICE

Содержание E-TEC 115



























































































Результаты поиска

Содержание E-TEC 115

Отзывы:

Похожие инструкции для E-TEC 115

Бренды по названию

Популярные бренды

Evinrude E-TEC 115, Оригинальное руководство пользователя

Результаты поиска

Содержание E-TEC 115

Отзывы:

Похожие инструкции для E-TEC 115

Бренды по названию

Популярные бренды