GB
OPERATING INSTRUCTIONS
PD-C360i/24 KNX UP
(EP10427428)
PD-C360i/24 KNX ECO UP (EP10427435)
www.esylux.com 2/13
LIGHT CHANNEL OBJECTS
Object 0: “Input: Lock light channel” (length = 1 bit)
The switching/dimming outputs for the light channel are locked with an ON
telegram and unlocked with an OFF telegram.
Parameters can be set to determine the status of the light channel after locking
and unlocking.
Object 1/2: “Input: Light channel manual ON/OFF” (length = 1 bit)
Note: essential when in semi-automatic mode!
Manual operation is maintained when persons are present until the switch-
off delay time has elapsed if “while presence” is set in the parameters. Light
measurement is not active if the parameter “With disabled light processing
during off-period” has been selected. After this, the detector switches to normal
operating mode. Manual operation has no impact on motion detection. The
function is transmitted to communication objects 5/6.
Object 3/4: “Input: Light channel manual dimming” (length = 4 bits)
not for version PD-C360i/24 KNX ECO UP
Function: active when constant light control/regulation has been selected!
Input for dim up/dim down KNX touch sensors. Writing on this object manually
overrides the light channel and the commands are transmitted to the dimming
actuator via object 7.
Manual operation is maintained when persons are present until the switch-
off delay time has elapsed if “while presence” is set in the parameters. Light
measurement is not active if “With disabled light processing during off-period”
has been selected. After this, the detector switches to normal operating mode.
Manual operation has no impact on motion detection.
Object 5/6: “Input: Light channel manual dim value” (length = 1 byte)
not for version PD-C360i/24 KNX ECO UP
Function: active when constant light control/regulation has been selected!
Input to preset dim values. Writing on this object manually overrides the light
channel and the values are transmitted to the dimming actuator via objects
8 and 9.
Manual operation is maintained when persons are present until the switch-
off delay time has elapsed if “while presence” is set in the parameters. Light
measurement is not active if “With disabled light processing during off-period”
has been selected. After this, the detector switches to normal operating mode.
Manual operation has no impact on motion detection.
Object 7: “Input: Light channel control/regulating without presence” (length = 1 bit)
not for version PD-C360i/24 KNX ECO UP
Operating mode: controlling
This object can be used to enable light control without presence.
Operating mode: regulating
This object can be used to enable light regulation without presence.
Object 8: “Output: Light channel ON/OFF” (length = 1 bit)
If artificial lighting is required (switching threshold 1/set value via parameter)
and persons are present, the output sends an ON telegram.
If natural light is sufficient and/or no persons are present, an OFF telegram is
sent once the switch-off delay time has elapsed.
Object 9: “Output: Light channel 2 ON/OFF” (length = 1 bit)
Function: switching - only available with switching function!
If artificial lighting is required (difference between switching threshold 2 and
switching threshold 1 via parameter) and persons are present, the output
sends an ON telegram.
If natural light is sufficient and/or no persons are present, an OFF telegram is
sent once the switch-off delay time has elapsed.
Object 10/11: “Output: Light channel dimming” (length = 4 bits)
not for version PD-C360i/24 KNX ECO UP
Function: constant light control/regulation
Telegrams can be transmitted to the dimming actuator via this object by
manually pressing and holding down a touch sensor (object 2). Only active
when “constant light control/regulation” has been enabled!
Object 12: “Output: Light channel dim value 1” (length = 1 byte)
not for version PD-C360i/24 KNX ECO UP
Function: constant light control/regulation
If artificial lighting is required and persons are present, the output sends a
value telegram (1 byte).
If natural light is sufficient (controller to minimum) and/or no persons are
present, the lighting is set to 0% or the device switches to orientation lighting
once the switch-off delay time has elapsed. Only active when “constant light
control/regulation” has been enabled!
Object 13: “Output: Light channel dim value 2” (length = 1 byte)
not for version PD-C360i/24 KNX ECO UP
Function: constant light control/regulation
If artificial lighting is required and persons are present, the output sends a
value telegram (1 byte).
If natural light is sufficient (controller to minimum) and/or no persons are
present, either 0% is sent or the device switches to orientation lighting once
the switch-off delay time has elapsed.
Option to offset dim value 2 and dim value 1 via parameter. Only active when
“constant light control/regulation” has been enabled!
Object 14: “Input: Light channel 1 switching threshold” (length = 2 bytes)
(Operating mode: switching)
This object can be used to specify the switching threshold (lux) for channel 1
via telegram. This is only available if “switching threshold via telegram” has
been selected.
Object 14: “Input: Light channel set value control” (length = 2 bytes)
not for version PD-C360i/24 KNX ECO UP
(Operating mode: controlling)
This object can be used to specify the set value (lux) for light control via telegram.
This is only available if “switching threshold via telegram” has been selected.
Object 14: “Input: Light channel regulating lower light value” (length = 2 bytes)
not for version PD-C360i/24 KNX ECO UP
(Operating mode: regulating)
This object can be used to specify the lower light value (lux) for light regulation
via telegram. This is only available if “switching threshold via telegram” has
been selected.
Object 15: “Input: Light channel 2 switching threshold” (length = 2 bytes)
(Operating mode: switching)
This object can be used to specify the switching threshold (lux) for channel 2
via telegram. This is only available if “switching threshold via telegram” has
been selected.
Object 15: “Input: Light channel regulating upper light value” (length = 2 bytes)
not for version PD-C360i/24 KNX ECO UP
(Operating mode: regulating)
This object can be used to specify the upper light value (lux) for light regulation
via telegram. This is only available if “switching threshold via telegram” has
been selected.
