Epson TM-C3500 Series Скачать руководство пользователя страница 40

Страница: 40 / 240

Shutter Adjustment

Turn the printer OFF.

Press down the release lever, and pull it to the front to open the roll

paper cover.

Refer to the shutter adjustment method label on the top of the printer,

and open or close the shutters on the platen to match the width of the

paper. If the shutter is set incorrectly, paper may be jammed or get dirty.

Paper/backing width (mm)

Shutter open/close status

30 mm {1.18"} or more, less than 62 mm {2.44"}

Close all shutters.

62 mm {2.44"} or more, less than 79 mm {3.11"}

Open only the most inward shutters.

79 mm {3.11"} or more, less than 97 mm {3.82"}

Open only the 2 most inward shutter rows.

97 mm {3.82"} or more, less than 112 mm {4.41"}

Open only the 3 most inward shutter rows.

112 mm {4.41"}

Open all shutters.

Open

Содержание TM-C3500 Series

















































































































































































































































Результаты поиска

Содержание TM-C3500 Series

Отзывы:

Похожие инструкции для TM-C3500 Series

Бренды по названию

Популярные бренды

Epson TM-C3500 Series, Техническое справочное руководство

Результаты поиска

Содержание TM-C3500 Series

Отзывы:

Похожие инструкции для TM-C3500 Series

Бренды по названию

Популярные бренды