Epson TM-C3500 Series Скачать руководство пользователя страница 149

Страница: 149 / 240

Chapter 3 Handling

149

When paper is loaded,

it is fed and an error

occurs

For Die-cut label

(Gap) and Transparent

die-cut label

The paper you are

using does not match

the [Media detection

settings].

Check the paper you are using and

the printer’s [Media detection set-

tings].

See

"Media detection settings" on

page 115

The transmittance of

the paper you are

using is out of the

specifications.

The label gap may not be

detected. Infrared light is used to

detect the label gap; therefore, the

infrared transmittance of the back-

ing paper must be higher than the

specified value and that of the

label part must be lower than the

specified value.

Check the paper specifications,

and use the paper that matches

the printer specifications.

You may be able to detect the gap

by performing [Adjust the Label

Gap Detection Sensor].

On the printer driver’s [Printer Utili-

ties] tab, click [Printer Setting Utility].

When the PrinterSetting screen is

displayed, click [Printer Adjustment]

- [Sensor Adjustment] and perform

[Adjust the Label Gap Detection

Sensor].

See

"Sensor Adjustment" on page

136

An error has occurred

in the sensor.

If the printer has been working

properly so far, the sensor may be

malfunctioning. Contact your

dealer for repairs.

Trouble

Description

Recovery method

Image/

Illustra-

tion

Содержание TM-C3500 Series

















































































































































































































































Результаты поиска

Содержание TM-C3500 Series

Отзывы:

Похожие инструкции для TM-C3500 Series

Бренды по названию

Популярные бренды

Epson TM-C3500 Series, Техническое справочное руководство

Результаты поиска

Содержание TM-C3500 Series

Отзывы:

Похожие инструкции для TM-C3500 Series

Бренды по названию

Популярные бренды