Epson Stylus Pro 7000 Series Скачать руководство пользователя страница 99

Страница: 99 / 147

6-7

Maintaining and Transporting the Printer

6-7

Replacing Ink Cartridges

When one of the

Ink Out

lights is flashing (and

INK LOW

is displayed on

the control panel), the corresponding cartridge is almost out of ink. Make
sure you have a replacement cartridge. When the light stays on and

INK

OUT

is displayed, the cartridge is empty. You must replace the cartridge

before you can continue printing.

Use the following EPSON ink cartridges:

Before you start, make sure the printer is on. Then follow these steps to
replace an ink cartridge:

1. Note the color of the

Ink Out

light that is on or flashing. This is the

cartridge that you need to replace.

2. Open the ink compartment cover.

•

Black

T460011

•

Light cyan

T465011

•

Cyan

T463011

•

Light magenta T464011

•

Magenta

T462011

•

Yellow

T461011

Caution

For best results, use
genuine EPSON
cartridges and do not
refill them. Damage to
your printer attributable
to the use of other
consumables is not
covered by EPSON’s
warranty. Color accuracy
may vary considerably if
you use non-EPSON inks.

Caution

Leave the empty
cartridge in the printer
until you are ready to
replace it.

Содержание Stylus Pro 7000 Series




















































































































































Результаты поиска

Содержание Stylus Pro 7000 Series

Отзывы:

Epson Stylus Pro 7000 Series, Руководство принтера, Страница: 99 / 147

Результаты поиска

Содержание Stylus Pro 7000 Series

Отзывы: