Epson Stylus Pro 7000 Series Скачать руководство пользователя страница 11

Страница: 11 / 147

Introduction

Using This

Printer Guide

This guide contains the following information:

Chapter 1

Chapter 1 explains how to install an interface card in the printer, how to
connect the printer, and how to install the EPSON drivers.

Chapter

Chapter 2

2 gives instructions for loading roll paper and cut sheets, printing

on both EPSON and non-EPSON media, and setting paper configurations.

Chapter 3

Chapter 3 explains how to use the EPSON printer drivers and utilities for
Macintosh computers.

Chapter 4

Chapter 4 explains how to use EPSON printer drivers and utilities for
Windows computers.

Chapter

Chapter 5

5 describes how to monitor the printer’s status and respond to error

messages on the control panel.

Chapter 6

Chapter 6 gives instructions for cleaning and aligning the print head,
replacing ink cartridges and the cutter blade, and cleaning and transporting
the printer.

Chapter 7

Chapter 7 provides troubleshooting tips and solutions for problems
involving print quality, printer operation, and paper handling.

Chapter 8

Chapter 8 provides the technical details on your printer, paper requirements,
and ink cartridges.

The Appendix

Appendix

Appendix gives instructions for configuring the printer.

An Index

Index

Index is included at the end of the book.

Содержание Stylus Pro 7000 Series




















































































































































Результаты поиска

Содержание Stylus Pro 7000 Series

Отзывы:

Epson Stylus Pro 7000 Series, Руководство принтера, Страница: 11 / 147

Результаты поиска

Содержание Stylus Pro 7000 Series

Отзывы: