Epson Stylus Pro 7000 Series Скачать руководство пользователя страница 115

Страница: 115 / 147

7-5

Resolving Problems

7-5

Solving Operational Problems

If you can’t turn the printer on, if it stops printing unexpectedly, or if
nothing prints, check the following:

•

The printer is turned on and the

Operate

light is on.

•

The printer is plugged securely into a working electrical outlet that’s not
controlled by a switch or timer.

•

If you’re using the RIP Station 5100, make sure the interface cable is
securely connected to the printer and RIP and the RIP is turned on.
Check the RIP Station 5100

User Guide

for additional troubleshooting

solutions.

If none of these suggestions help, try the solutions below:

Operational problems

Problem

Possible cause

Solution

The printer stops
printing
unexpectedly.

If the

Pause

light is flashing, the

printer is performing a maintenance
procedure or waiting for ink to dry.

Check the display message and lights on the
control panel. Wait until the

Pause

light stops

flashing.

An error has occurred.

Check the display message and lights on the
control panel. Follow the instructions for the
message on page 5-5.

The printer sounds
like it’s printing, but
nothing prints.

Print head nozzles are clogged.

Run a nozzle check and cleaning cycle (page 6-1).

Содержание Stylus Pro 7000 Series




















































































































































Результаты поиска

Содержание Stylus Pro 7000 Series

Отзывы:

Epson Stylus Pro 7000 Series, Руководство принтера, Страница: 115 / 147

Результаты поиска

Содержание Stylus Pro 7000 Series

Отзывы: