Epson Stylus Color C60 Скачать руководство пользователя страница 139 | Manualshive

Страница: 139 / 188

background image

EPSON Stylus C50/C60/C61/C62

Revision C

Maintenance

Overview

131

1.

Select the “EPSON Status Monitor 3” in the printer driver utility, and make sure
that the printer is in stand-by state by using the Status monitor 3. If the printer is in
stand-by state, the following figure is indicated on the monitor.

Figure 6-1. Status monitor 3 indication

2.

Select the “Head Cleaning” in the printer driver utility, and perform the printhead
cleaning. After performing the printhead cleaning operation, print a nozzle check
pattern by selecting the “Nozzle Check“. If you repeat the printhead cleaning
operation without selecting the “Nozzle Check”, CL1, the weakest cleaning, will
be repeated.

Figure 6-2. Head cleaning function in the printer driver utility

Maintenance request error (Maintenance call error)
Ink is used for the printhead cleaning operation as well as the printing operation.
When the ink is used for the printhead cleaning operation, the ink is drained to the
Waste drain ink pad and the amount of the waste ink is stored as the waste ink
counter into the EEPROM on the Main board. Due to this, when the waste ink
counter has reached the limit (Waste ink counter = Protection counter A = 21560
points for the Stylus C50,

23270

points

for the Stylus C60/

C61/C62

) of the

absorbing capability of the Waste drain ink pad, the Maintenance call error is
indicated on Status monitor 3 as following figure.

Figure 6-3. Maintenance error indication in STM3

In this case, replace to new Waste drain ink pad and clear the waste ink counter stored
into the EEPROM. The waste ink counter can be reset only from the Adjustment
program because this printer dose not have the waste ink counter reset function by the
control panel SW. As for the procedure, refer to Chapter 5 Adjustment.
In your repair activity, check the waste ink counter along with the firmware version,
Main board checker program version and nozzle check pattern on the nozzle check
pattern printing. If the waste ink counter is closed to its limit, recommend that the
Waste drain ink pad will be replaced with new one. This is because the "Maintenance
request error" will may occur after returning the repaired product to the customer.

* : Refer to the right lower side.

* : Refer to the right lower side.

* : The explanations for STM3 of the Stylus C50 are the same as the Stylus C60/C61/C62
      completely except the followings.
        1) Printer name, 2) Figure of the printer

3) T-code for Bk ink cartridge (SC50:T026, SC60/

C61

:

T028

,

SC62

:

T040

)

4) T-code for Col. ink cartridge (SC50/C60/

C61

:

T029

,

SC62

:

T041

)

«
...
137
138
139
140
141
...
»

Содержание Stylus Color C60





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Stylus Color C60

Бренд: 3M Страницы: 26

Бренд: Samsung Страницы: 15

Бренд: Olivetti Страницы: 39

Бренд: Labau Страницы: 19

Бренд: Barco Страницы: 2

Бренд: Gates Underwater Products Страницы: 49

Бренд: Gates Underwater Products Страницы: 45

Бренд: IFM Страницы: 12

Бренд: IFM Страницы: 13

Efector 200 Series

Бренд: IFM Страницы: 4

Бренд: IFM Страницы: 33

Бренд: Oki Страницы: 48

Бренд: Oki Страницы: 65

Бренд: Oki Страницы: 44

Бренд: Oki Страницы: 36

Бренд: OHAUS Страницы: 28

Бренд: National Cycle Страницы: 3

Бренд: Pitney Bowes Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды