Epson Stylus Color C60 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 188

background image

EPSON Stylus C50/C60/C61/C62

Revision C

Operating Principles

Electrical Circuit Operating Principles

46

2.2.2 C418 MAIN/MAIN-B/C429 Main Board

The logic circuit of the C418 Main/Main-B/C429 Main board is composed of the
follows;

Logic line (ASIC, DRAM, P-ROM, EEPROM and so no)

Motor control/drive circuit (CR motor/PF motor)

Head control/drive circuit

Interface control circuit (Parallel I/F, USB I/F)

Sensor circuit

Reset circuit

EEPROM circuit

Switch circuit

LED circuit

The printer mechanism is controlled by the above circuits. Following explains the
major characteristics of this Main board.

Timer IC & Lithium battery are not mounted
Unlike the previous printer (Stylus COLOR 680), the Timer IC and the Lithium
battery are not mounted on these Main boards. So, these printers perform the
Power-on cleaning or Timer cleaning based on the time command which is sent
from the PC through the printer driver. As for the details, refer to 2.1.6.

Use of the 3.3V chips in the logic circuit
The 3.3V regulator (IC8) on the C418 Main/Main-B/C429 Main board generates
3.3VDC by pressuring down the 5VDC to drive several chips for the logic circuit.

Table 2-7. 3.3VDC drive chips & 5VDC drive chips

Unlike the previous printer (Stylus COLOR 680), the panel board is eliminated
and the switches/LED lights are mounted on the Main board.

The transceiver with USB I/F is built in the CPU.

D-RAM

Stylus C50

: 1Mbit D-RAM is mounted on the Main board.

Stylus C60

: 4Mbit D-RAM is mounted on the Main board.

One ASIC controls the all functions on the Main board.
See figure 2-17. for the C418 Main/Main-B board block diagram.

Figure 2-20. Block diagram for the C418 Main/Main-B/C429 Main board

5VDC

3.3VDC

Motor driver (IC10/11)

Reset IC (IC2)

EEPROM (IC3)

Parallel controller (IC7)

ASIC (IC1)

D-RAM (IC5/IC4)

P-ROM (IC6/IC5)

Parallel controller (IC7)

Common driver (IC9/IC19)

P-ROM

(SOJ) 8M
(IC6/IC5)

Address

Data

D-RAM 4M

(IC5/IC4)

E01A21CB

CPU (IC1)

Reset IC

(IC2)

EEPROM

(IC3)

Motor Driver

(IC10)

Motor Driver

(IC11)

Common

Driver (IC9/IC19)

Parallel I/F IC

(IC7)

Q2&Q3

CN3
USB

CN4

CN7

CN12

CN9

CN8

CN1 Parallel I/F

Head

PF Motor

CR Motor

HP/PE Sensor

CR2

* There is difference of IC location between the Stylus C50 and the Stylus C60.
(A/B) : A means the location for the Stylus C50.
B means the location for the Stylus C60.

* There is difference of IC location between the Stylus C50 and the Stylus C60.
(A/B) : A means the location for the Stylus C50.
B means the location for the Stylus C60.

«
...
52
53
54
55
56
...
»

Содержание Stylus Color C60





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Stylus Color C60

Бренд: Canon Страницы: 86

Бренд: Canon Страницы: 20

Бренд: Samsung Страницы: 341

CLP-770ND - Color Laser Printer

Бренд: Samsung Страницы: 2

CLP 610ND - Color Laser Printer

Бренд: Samsung Страницы: 114

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 15

CLP 600N - Color Laser Printer

Бренд: Samsung Страницы: 227

CLP 600N - Color Laser Printer

Бренд: Samsung Страницы: 118

CLP 300N - Network-ready Color Laser Printer

Бренд: Samsung Страницы: 94

3561ND - B/W Laser Printer

Бренд: Samsung Страницы: 252

3561ND - B/W Laser Printer

Бренд: Samsung Страницы: 127

2252W - Printer - B/W

Бренд: Samsung Страницы: 201

ML 2851ND - B/W Laser Printer

Бренд: Samsung Страницы: 89

Бренд: AAMP of America Страницы: 6

Бренд: Abus Страницы: 2

Бренд: RayTek Страницы: 2

Бренд: Ace Bayou Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды