Epson Stylus Color C60 Скачать руководство пользователя страница 125

Страница: 125 / 188

EPSON Stylus C50/C60/C61/C62

Revision C

Disassembly and Assembly

Disassembly

117

When assembling the Printer mechanism to the Lower housing,

Make sure to set the Main frame reinforcing plate correctly
at the rightmost screw.

Figure 4-57. Reinforcing plate setting position

Avoid to damage the coated surface of the PF roller by using
the OHP sheet as shown figure below.

Figure 4-58. Printer mechanism assembling(1)

Reinforcing plate

OHP sheet

Do not damage the tooth of the Spur gear 60 of the Paper
eject roller because its roller is not fixed.

Fasten three screws (C.B.S. SCREW 3 x10 F/Zn) for
securing the Printer mechanism to the Lower housing.

Figure 4-59. Printer mechanism assembling(2)

Tightening torque for each screw is as follows.

• C.B.S. SCREW, 3 x 10, F/Zn (3pcs) : 6 ± 1kgf.cm

Be careful not to drop the Cap unit from the Main frame.

Do not touch the sealing rubber portion and the cleaner head
of the Cap unit.

Make sure that the Cap unit is correctly fixed to the Main
frame.

Make sure to set the end of ink tube correctly.

Make sure to place the Ink tube as shown figure below

Figure 4-60. Ink tube setting position

Ink tube

Содержание Stylus Color C60





























































































































































































Результаты поиска

Содержание Stylus Color C60

Отзывы:

Похожие инструкции для Stylus Color C60

Бренды по названию

Популярные бренды

Epson Stylus Color C60, Руководство по обслуживанию

Результаты поиска

Содержание Stylus Color C60

Отзывы:

Похожие инструкции для Stylus Color C60

Бренды по названию

Популярные бренды