Epson Stylus Color C60 Скачать руководство пользователя страница 88

Страница: 88 / 188

EPSON Stylus C50/C60/C61/C62

Revision C

Troubleshooting

Unit Level Troubleshooting

Poor printing

quality

Operation

Horizontal banding

against CR movement

direction

PF motor

The accuracy of the PF motor is lowered.

Refer to Table 3-19

PF roller unit

The PF roller has any foreign material.

The PF roller is damaged

The Spur gear 60 is damaged.

Printer driver

The printer driver setting is not suitable.

Printhead

Each segment is printed correctly in the nozzle check pattern.

Star wheel mark

Front frame

The Front frame is bent down.

The Star wheel comes off.

Paper eject roller unit

The Paper eject roller shaft comes off.

Insufficient top margin

LD roller unit

The friction of the LD roller is lowered.

Ink blur

Printer driver

The printer driver setting is not suitable.

Printhead

The Head ID is not input correctly.

Ink stain

Front frame

The Front frame has the ink stain somewhere.

The Front frame is bent up.

Lower housing

The Lower housing has the ink stain somewhere.

Paper eject roller unit

The Paper eject roller has ink stain somewhere.

The Spur gear 60 comes off.

Paper guide upper/left

The Paper guide upper/left has ink stain somewhere.

PF roller unit

The PF roller has ink stain somewhere.

Printhead

The Printhead has the ink drop on the nozzle surface.

The Printhead cover has the ink drop.

Wrinkle

ASF unit

The Hopper pad/LD pad is correctly not pasted on the dent.

Table 3-18. Poor printing quality

Error condition

Occurrence

timing

CR position at the

power on timing

Phenomenon

Unit/Part name

Possible cause

Check table

Содержание Stylus Color C60





























































































































































































Результаты поиска

Содержание Stylus Color C60

Отзывы:

Похожие инструкции для Stylus Color C60

Бренды по названию

Популярные бренды

Epson Stylus Color C60, Руководство по обслуживанию

Результаты поиска

Содержание Stylus Color C60

Отзывы:

Похожие инструкции для Stylus Color C60

Бренды по названию

Популярные бренды