Epson PERFECTION V10 Скачать руководство пользователя страница 46

Страница: 46 / 77

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

DISASSEMBLY/ASSEMBLY

Disassembly of AFL

4.5 Disassembly of AFL

4.5.1 Separation of AFL Upper Housing Assy/AFL Lower

Housing Assy

1. Disengage the Hinge.

(4.3.1 Hinge Disengagement on page 34)

2. Slide the AFL Housing Mat in the direction of the arrow, releasing it from the

socket of the AFL Unit and remove it.

3. Remove the Film Holder Assy from the AFL Unit.

Figure 4-31. Removing the AFL Housing Mat

4. Open the Film Ejection Cover following the steps below.

1. Push the knobs of the Film Ejection Cover from both sides.
2. Open the Film Ejection Cover.

Figure 4-32. Opening the Film Ejection Cover

5. Remove the seven screws (C.B.P. 3x8, 5-7 kgf.) and separate the AFL Upper

Housing Assy and the AFL Lower Housing Assy.

Figure 4-33. Removing the AFL Upper Housing Assy

Socket

Film Holder Assy

position

AFL Unit

AFL Housing Mat

Film Holder

Film Ejection Cover

Knob

C.B.P. 3x8

AFL Lower Housing Assy

AFL Upper Housing Assy

Содержание PERFECTION V10














































































Результаты поиска

Содержание PERFECTION V10

Отзывы:

Похожие инструкции для PERFECTION V10

Бренды по названию

Популярные бренды

Epson PERFECTION V10, Руководство по обслуживанию

Результаты поиска

Содержание PERFECTION V10

Отзывы:

Похожие инструкции для PERFECTION V10

Бренды по названию

Популярные бренды