Epson PERFECTION V10 Скачать руководство пользователя

Страница: 21 / 77

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

OPERATING PRINCIPLES

Engine Operation Outline

AFL FILM FEEDING MECHANISM (PERFECTION V350 PHOTO)

The AFL Film Feeding Mechanism is a mechanism to feed 35mm strip films by the
motor drive.

The AFL drive is transmitted to the AFL Motor Belt by a route as shown below.

Figure 2-7. Film Feeding Mechanism

Here are descriptions of mechanical operations from when setting document, and
scanning, and to the time of taking out the document.

1. The Film Sensor (Front) detects the film inserted into the film entry.

2. The AFL Motor starts to rotate clockwise and feed the film.

3. The film is sandwiched between the AFL Motor Belt and the Film Retainer Plate to be

fed.

4. The Film Sensor (Rear) detects the film.

(The Film Sensor (Rear) determines that film jams occurred when it cannot detect the
film within the specified time.)

5. Carry out scanning.

6. After a lapse of specified time, the AFL Motor starts to rotate counterclockwise to exit

the film.

AFL Motor

Combination Gear A

Combination Gear B

Combination Gear C

Drive Roller, Rear

AFL Motor Belt

AFL Motor

Combination

Gear A

Combination

Gear B

Combination

Gear C

Drive Roller, Rear

AFL Motor Belt

Film

Film Sensor (Front)

Film Sensor (Rear)

Film Retainer Plate

Содержание PERFECTION V10














































































Результаты поиска

Содержание PERFECTION V10

Отзывы:

Похожие инструкции для PERFECTION V10

Бренды по названию

Популярные бренды

Epson PERFECTION V10, Руководство по обслуживанию

Результаты поиска

Содержание PERFECTION V10

Отзывы:

Похожие инструкции для PERFECTION V10

Бренды по названию

Популярные бренды