Epson PERFECTION V10 Скачать руководство пользователя страница 40

Страница: 40 / 77

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

DISASSEMBLY/ASSEMBLY

Disassembly of Main Unit

5. Remove the three screws (C.C.P. 3X8, 5-7 kgf.cm) that secure the CR Motor Assy.

6. Remove the CR Motor Assy from the Lower Housing.

7. Remove the Damper from the CR Motor Assy.

Figure 4-16. Removing the CR Motor (1)

8. Remove the two washers and the two Gears, and remove the Timing Belt from the

CR Motor Assy.

Figure 4-17. Removing the CR Motor (2)

C.C.P. 3x8

Damper

CR Motor Assy

(Bottom side)

Timing Belt

Gears

Washers

After replacing the CR Motor, make sure to apply G-45 grease
to the specified area.

(Chapter 6 "MAINTENANCE" P58)

Make sure to loop the Timing Belt over the shaft with the
larger Gear.

Attach the Dampers so that the thick side of them comes to the
side with the Gears, as shown below.

Figure 4-18. Reassembling the CR Motor Assy

Damper

Timing Belt

Thick side

The larger Gear

Содержание PERFECTION V10














































































Результаты поиска

Содержание PERFECTION V10

Отзывы:

Похожие инструкции для PERFECTION V10

Бренды по названию

Популярные бренды

Epson PERFECTION V10, Руководство по обслуживанию

Результаты поиска

Содержание PERFECTION V10

Отзывы:

Похожие инструкции для PERFECTION V10

Бренды по названию

Популярные бренды