Epson PERFECTION V10 Скачать руководство пользователя

Страница: 36 / 77

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

DISASSEMBLY/ASSEMBLY

Disassembly of Main Unit

5. On the bottom side of the Upper Housing, disengage the four hooks that secure the

Button Cover, and remove the Optical Plate, Function Buttons, and Button Cover.

(Figure 4-6)

Figure 4-5. Removing the Optical Plate/Function Buttons/Button Cover

4.3.4 Hinge

1. Remove the Upper Housing.

(4.3.3 Upper Housing on page 35)

2. Remove the Hinge from the slot of the Upper Housing.

Figure 4-7. Removing the Hinge

When reassembling the Optical Plate, Function Buttons and the
Button Cover, refer to the figure below.

Figure 4-6. Reassembling the Optical Plate/Function Buttons/Button

Cover

Upper Housing

Bottom side

Hook

Button Cover

Optical Plate

Function Buttons

Button Cover

When reassembling the Hinge, attach it with its hook facing the
direction shown in the figure.

Hinge

Upper Housing

Slot

Hook of the Hinge

Содержание PERFECTION V10














































































Результаты поиска

Содержание PERFECTION V10

Отзывы:

Похожие инструкции для PERFECTION V10

Бренды по названию

Популярные бренды

Epson PERFECTION V10, Руководство по обслуживанию

Результаты поиска

Содержание PERFECTION V10

Отзывы:

Похожие инструкции для PERFECTION V10

Бренды по названию

Популярные бренды