Epson PERFECTION V10 Скачать руководство пользователя | Manualshive

Страница: 34 / 77

background image

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

DISASSEMBLY/ASSEMBLY

Disassembly of Main Unit

34

4.3 Disassembly of Main Unit

4.3.1 Hinge Disengagement

1. Open the Document Cover/TPU Unit/AFL Unit.

2. Hold and lift the Document Cover/TPU Unit/AFL Unit upward, and place it

horizontally.

Figure 4-2. Disengagement of the hinge (1)

3. Push the Document Cover/TPU Unit/AFL Unit towards the main unit, releasing

the 2 shafts from the hooks of the Hinge one by one.

Figure 4-3. Disengagement of the hinge (2)

C A U T I O N

When disengaging the Hinge, the Document Cover/TPU Unit/AFL
Unit may hit the scanner main unit and damage it. Place cushioning
material such as a cloth to the Hinge side of the scanner main unit
during operation to avoid damage.

C H E C K

P O I N T

Disengaging method of the Hinge, to remove the Document Cover/
TPU/AFL from the scanner main unit is common for Perfection
V10/V100 Photo/V200 Photo/V350 Photo. When removing the
Document Cover/TPU/AFL from the scanner main unit, follow the
procedure described below.

Document Cover/

TPU Unit/

AFL Unit

Hinge

Document Cover/TPU Unit/AFL Unit

Hook

Shaft

Before release

Hinge

Hook

Shaft

After release

Hinge

«
...
32
33
34
35
36
...
»

Содержание PERFECTION V10














































































Отзывы:

Нет отзывов

Похожие инструкции для PERFECTION V10

Бренд: Barco Страницы: 2

Бренд: Contex Страницы: 57

Бренд: Targus Страницы: 8

Бренд: Pyle Страницы: 14

Бренд: Marktrace Страницы: 9

Бренд: Sense Страницы: 11

Бренд: Plustek Страницы: 49

Бренд: Radio Shack Страницы: 32

WorkCentre Pro 423

Бренд: Xerox Страницы: 68

Бренд: Radio Shack Страницы: 44

Бренд: CAMAG Страницы: 25

Бренд: Panasonic Страницы: 44

Series Perfection 1240U Series

Бренд: Epson Страницы: 2

Series Perfection 1240U Series

Бренд: Epson Страницы: 57

Series Perfection 1240U Series

Бренд: Epson Страницы: 166

Бренд: Xerox Страницы: 2

Бренд: atiz Страницы: 8

IRISPEN EXPRESS 6 - FLYER

Бренд: I.R.I.S. Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды