Epson C11C640001 - LX 300+II B/W Dot-matrix Printer Скачать руководство пользователя

Страница: 78 / 129

Maintenance and Troubleshooting

= on,

= flashing

•••

= short series of beeps (three beeps)

•••••

= long series of beeps (five beeps)

Note:

The printer beeps once if you press a control panel button when the
corresponding function is not available.

Paper Out

Pause

•••

Continuous paper is not fed back to the
standby position.

Tear off the printed document at the
perforation; then press the

Load/Eject

button. The printer feeds the paper to the
standby position. Press the

Pause

button

to turn off the Pause light, if necessary.

•••

A single sheet of paper is not fully ejected.

Press the

Load/Eject

button to eject the

sheet. Then press the

Pause

button to turn

off the Pause light, if necessary.

•••

Paper is jammed in the printer.

Clear the paper jam as described on
page 93.

Pause

–

The print head is overheated.

Wait a few minutes; the printer resumes
printing automatically once the print
head has cooled.

All the lights on

the control panel

•••••

An unknown printer error has occurred.

Turn off the printer and leave it off for
several minutes; then turn on the printer
again. If the error recurs, contact your
dealer.

Panel light
state

Beep
pattern

Problem

Solution

Содержание C11C640001 - LX 300+II B/W Dot-matrix Printer


































































































































Результаты поиска

Содержание C11C640001 - LX 300+II B/W Dot-matrix Printer

Отзывы:

Похожие инструкции для C11C640001 - LX 300+II B/W Dot-matrix Printer

Бренды по названию

Популярные бренды

Epson C11C640001 - LX 300+II B/W Dot-matrix Printer, Справочное руководство

Результаты поиска

Содержание C11C640001 - LX 300+II B/W Dot-matrix Printer

Отзывы:

Похожие инструкции для C11C640001 - LX 300+II B/W Dot-matrix Printer

Бренды по названию

Популярные бренды