Epson C11C640001 - LX 300+II B/W Dot-matrix Printer Скачать руководство пользователя

Страница: 120 / 129

120

Product Information

Continuous paper

The minimum top and bottom margins above and below
the perforation are 0.17 inch (4.2 mm) each.

The minimum left and right margins are 0.51 inch (13 mm)
each.

The maximum paper width is 10.0 inches (254 mm).

The maximum printable width is 8.0 inches (203.2 mm). If
the paper size is substantially wider than this, the side
margins will be wider than the minimum, but the printable
width does not increase beyond 8.0 inches (203.2 mm).

Содержание C11C640001 - LX 300+II B/W Dot-matrix Printer


































































































































Результаты поиска

Содержание C11C640001 - LX 300+II B/W Dot-matrix Printer

Отзывы:

Похожие инструкции для C11C640001 - LX 300+II B/W Dot-matrix Printer

Бренды по названию

Популярные бренды

Epson C11C640001 - LX 300+II B/W Dot-matrix Printer, Справочное руководство

Результаты поиска

Содержание C11C640001 - LX 300+II B/W Dot-matrix Printer

Отзывы:

Похожие инструкции для C11C640001 - LX 300+II B/W Dot-matrix Printer

Бренды по названию

Популярные бренды